激光熔覆原位生成VC增强Fe-Ni基复合涂层的组织与硬度

详细信息    查看全文 | 推荐本文 |

英文篇名：Microstructure and hardness of in-situ synthesized VC-reinforced Fe-Ni-based composite coating by laser cladding 作者：张伟 ; 冯秋红 ; 王尔亦 ; 郑炉玉 ; 张伟中 英文作者：Zhang Wei;Feng Qiuhong;Wang Eryi;Zheng Luyu;Zhang Weizhong;Zhejiang Institute of Mechanical and Electrical Engineering;Institute of Laser Advanced Manufacturing,Zhejiang University of Technology;Zhejiang Machinery and Electrical Group; 关键词：复合材料 ; 激光熔覆 ; 显微组织 ; 硬度 ; 碳化钒 英文关键词：composites;;laser cladding;;microstructure;;hardness;;VC 中文刊名：JSRC 英文刊名：Heat Treatment of Metals 机构：浙江机电职业技术学院;浙江工业大学激光先进制造研究院;浙江省机电集团有限公司; 出版日期：2019-07-25 出版单位：金属热处理 年：2019 期：v.44;No.503 基金：浙江省公益技术应用研究项目(2017C31057,GG19E050018) 语种：中文; 页：JSRC201907048 页数：4 CN：07 ISSN：11-1860/TG 分类号：197-200

摘要

针对高速电梯制动瓦块材料耐高温磨损性差的问题,以V粉和Ni基合金粉末为原料,进行了激光熔覆原位生成VC增强Fe-Ni基复合涂层的试验,分析了不同粉末质量配比、不同工艺参数下熔覆层的组织演变规律和硬度性能。研究表明:通过原位反应可获得主要由VC、Cr_3C_2、Fe_3C和Ni-Fe固溶体组成的陶瓷复合涂层; VC的含量随V含量的增加而增加;在较低的扫描速度下,VC颗粒呈梅花状或菊花状弥散分布。当扫描速度较高时,VC呈胞状和块状,主要分布在晶界上; V含量10%、30%、50%对应的熔覆层平均硬度分别为562、715、908 HV0. 2。
        Aiming at the problem of poor high-temperature wear-resistance of brake block used in ultra-high speed elevator,the experiments of laser cladding for VC-Cr_3C_2-Fe_3C/Fe-Ni composite coating was prepared by using V powder and Ni-based alloy powder as cladding materials. The microstructure evolution and hardness properties of the cladding layer under different powder mass ratios and different process parameters were analyzed. The results show that the obtained ceramic composite coating is mainly composed of VC,Cr_3C_2,Fe_3C and Ni-Fe solid solution,and the content of VC increases with the increase of V content. At low scanning speeds,VC particles are distributed in plum blossom-like or chrysanthemum-like,but when the scanning speed is high,VC is mainly distributed on the grain boundary in cellular-like or block shape. When the V content is 10%,30% and 50%,the average hardness of the coating are 562 HV0. 2,715 HV0. 2 and 908 HV0. 2,respectively.

引文

[1]殷勤.电梯零部件设计[M].广州:中山大学出版社,2014.
    [2]上海市电梯行业协会.电梯—原理·安装·维修[M].北京:中国纺织出版社,2015.
    [3]左铁钏. 21世纪的先进制造—激光技术与工程[M].北京:科学出版社,2007.
    [4]曹凤国.激光加工[M].北京:化学工业出版社,2015.
    [5]张伟.钼对高铬铸铁激光熔覆层组织和硬度的影响[J].金属热处理,2016,41(3):170-174.Zhang Wei. Influence of Mo on microstructure and hardness of high Cr cast iron laser cladding layer[J]. Heat Treatment of Metals,2016,41(3):170-174.
    [6]花国然,黄因慧,赵剑峰,等.激光熔覆纳米Al2O3等离子喷涂陶瓷涂层[J].中国有色金属学报,2004,14(2):199-203.Hua Guoran,Huang Yinhui,Zhao Jianfeng,et al. Plasma-sprayed ceramic coating by laser cladding of Al2O3nano-particles[J]. The Chinese Journal of Nonferrous Metals,2004,14(2):199-203.
    [7]冯淑容,张述泉,王华明.钛合金激光熔覆硬质颗粒增强金属间化合物复合涂层耐磨性[J].中国激光,2012,39(2):60-65.Feng Shurong Zhang Shuquan Wang Huaming. Wear resistance of laser clad hard particles reinforced intermetallic composite coating on TA15alloy[J]. Chinese Journal of Lasers,2012,39(2):60-65.
    [8]石世宏,傅戈雁,王新林,等.多冲接触载荷下不锈钢零件激光表面熔覆层组织及其失效行为[J].金属热处理,2002,27(3):16-19.Shi Shihong,Fu Geyan,Wang Xinlin,et al. Microstructure and failure behavior of laser cladding layer for stainless steel components worked under repeated impact load condition[J]. Heat Treatment of Metals,2002,27(3):16-19.
    [9]张伟,姚建华,张利春.激光熔覆原位生成VC-Fe3C/Fe-Ni复合涂层的组织与性能[J].复合材料学报,2017,34(1):142-151.Zhang Wei,Yao Jianhua,Zhang Lichun. Microstructure and properties of in-situ synthesized VC-Fe3C/Fe-Ni composite coating made by laser cladding[J]. Acta Materiae Compositae Sinica, 2017, 34(1):142-151.
    [10]张伟.激光熔覆Fe45与超细VC复合涂层的组织和性能[J].材料热处理学报,2016,37(2):212-215.Zhang Wei. Microstructure and properties of VC-Fe composite coating prepared by laser cladding technology[J]. Transactions of Materials and Heat Treatment,2016,37(2):212-215.
    [11]贺星,王晶,孔德军,等. Ti C对激光熔覆Ti C-Ti-Al涂层结构与性能的影响[J].金属热处理,2018,43(8):39-44.He Xing, Wang Jing, Kong Dejun, et al. Effect of Ti C on microstructure and properties of Ti C-Ti-Al coating prepared by laser cladding[J]. Heat Treatment of Metals,2018,43(8):39-44.