微心PDC钻头设计及现场试验

详细信息    查看全文 | 推荐本文 |

英文篇名：Design and Field Application of a Micro-Coring PDC Bit 作者：田京燕 ; 徐玉超 英文作者：TIAN Jingyan;XU Yuchao;Drilling Technology Research Institute,Sinopec Shengli Oilfield Service Corporation; 关键词：微心PDC钻头 ; 岩屑录井 ; 结构设计 ; 实验室试验 ; 现场试验 ; 机械钻速 英文关键词：micro-coring PDC bit;;cuttings logging;;structure design;;laboratory experiments;;field tests;;penetration rate 中文刊名：SYZT 英文刊名：Petroleum Drilling Techniques 机构：中石化胜利石油工程有限公司钻井工艺研究院; 出版日期：2018-10-19 13:55 出版单位：石油钻探技术 年：2019 期：v.47;No.223 基金：国家科技重大专项“致密油藏开发钻井技术优化及集成”(编号:2017ZX05072-003)资助 语种：中文; 页：SYZT201901012 页数：4 CN：01 ISSN：11-1763/TE 分类号：69-72

摘要

为了解决普通PDC钻头形成的岩屑细碎、无法满足岩屑录井,而采用牙轮钻头进尺少、机械钻速低又存在掉牙轮风险的问题,设计了微心PDC钻头。介绍了微心PDC钻头整体结构设计和结构参数优化方法,设计制造了小尺寸微心钻头,进行了室内取心试验和提速试验;结合临盘油田街403井和胜坨油田坨202井实钻地层的岩性特征,分别设计制造了φ215. 9 mm微心PDC钻头,进行了现场试验。室内试验和现场试验结果均显示:该钻头获取的岩屑较大,大小与牙轮钻头产生的钻屑相当,能满足岩屑录井的要求;而且,钻头进尺和机械钻速与普通PDC钻头相当,与牙轮钻头相比有明显提高。研究结果表明,微心PDC钻头可以代替牙轮钻头在岩屑录井井段使用,并能达到提速提效的目的。
        During coring,the cuttings obtained by an ordinary PDC bit are broken into small bits and cannot meet the minimum necessary conditions for logging cuttings. Further,the cone bit has small footage,low ROP and there are high risks of cone breakage. In order to overcome these challenges,a micro-coring PDC bit was designed.This paper describes the overall structural design and also describes the best method for optimizing structural parameters for the micro-coring PDC bit. Aligning with the results of mechanical analysis,a small-size bit was designed and manufactured,and laboratory coring experiments and acceleration experiments were carried out. Using specifications developmed from the formation lithology from Well Jie 403 in Linpan Oilfield and Well Tuo 202 in Shengtuo Oilfield,a φ215. 9 mm micro-coring PDC bit was designed and manufactured. The bit was then sent to the field where it was put into use in order to verify the design. Both the results of laboratory experiments and the field tests showed that the cuttings obtained by this bit were relatively large and the size was equivalent to that drilled by a cone bit,which could meet the requirements of cuttings logging. In addition,the bit footage and ROP were similar to that of ordinary PDC bit,and the efficiency was significantly improved compared to the cone bit. The results showed that the microcore PDC bit could replace the cone bit in the interval for logging the cuttings,and could improve the efficiency due to its higher ROP.

引文

[1]田京燕.PDC钻头三维设计软件的开发[J].石油机械,2009,37(5):32-34.TIAN Jingyan.PDC bit 3D design software development[J].China Petroleum Machinery,2009,37(5):32-34.
    [2]AADNOY B S,LOOYEH R.钻井岩石力学[M].韩来聚,王宗钢,冯光通,等译.东营:中国石油大学出版社,2013:6-58.AADNOY B S,LOOYEH R.Petroleum rock mechanics drilling operations and well design[M].Translated by HAN Laiju,WANGZonggang,FENG Guangtong,et al.Dongying:China of University Petroleum Press,2013:6-58.
    [3]刘竞,高含,陈光碧,等.微取心PDC钻头试验及评价[J].钻采工艺,2014,37(3):34-35.LIU Jing,GAO Han,CHEN Guangbi,et al.Test and evaluation of micro core PDC bit[J].Drilling&Production Technology,2014,37(3):34-35.
    [4]汪海阁,王灵碧,纪国栋,等.国内外钻完井技术新进展[J].石油钻采工艺,2013,35(5):1-12.WANG Haige,WANG Lingbi,JI Guodong,et al.Advances in well drilling and completion technologies for domestic and overseas[J].Oil Drilling&Production Technology,2013,35(5):1-12.
    [5]黄英勇,李根生,宋先知,等.PDC钻头定向喷嘴井底流场数值模拟[J].石油钻探技术,2011,39(6):99-103.HUANG Yingyong,LI Gensheng,SONG Xianzhi,et al.Numerical simulation of bottomhole flow field of PDC bit with orientation nozzle[J].Petroleum Drilling Techniques,2011,39(6):99-103.
    [6]徐玉超.定向井PDC钻头受力模型及优化设计研究[D].青岛:中国石油大学(华东),2008.XU Yuchao.Mechanical model and optimizing design of oriented PDC bit[D].Qingdao:China University of Petroleum(Huadong),2008.
    [7]DESCHAMPS B,DESMETTE S D J,DELWICHE R,et al.Drilling to the extreme:the micro-coring bit concept[R].SPE 115187,2008.