型钢混凝土剪力墙基于位移的变形能力设计方法

英文篇名：Displacement-based deformation capacity design method of steel reinforced concrete shear walls
中文刊名：建筑结构
英文刊名：Building Structure
作者：白亮 ; 梁兴文
英文作者：Bai Liang~1 ; Liang Xingwen~2(1 School of Civil Engineering ; Chang'an University ; Xi'an 710061 ; China ; 2 Key Laboratory for Structural Engineering andEarthquake Resistance of China Education Ministry ; Xi'an University of Architecture and Technology ; Xi'an 710055 ; China)
中文关键词：型钢混凝土剪力墙 ; 延性 ; 配箍率 ; 轴压比
英文关键词：SRC shear walls ; ductility ; value of stirrup content ; axial compression ratio
出版日期：2010-04-25
机构：长安大学建筑工程学院;西安建筑科技大学结构工程与抗震教育部重点实验室;
年：2010
期：04
出版单位：建筑结构

摘要

为了研究型钢混凝土(SRC)剪力墙的变形能力,利用其截面变形条件和平衡条件,建立了截面的屈服曲率与极限曲率的计算公式,并根据剪力墙曲率延性系数与位移延性系数的关系,用数值分析方法计算了SRC剪力墙的位移延性系数。通过计算分析,得到了SRC剪力墙的轴压比、边缘约束区箍筋配箍特征值、墙体高宽比与位移延性系数之间的关系。研究结果表明,适当增加SRC剪力墙约束钢筋的配箍特征值及限制墙体轴压比,可以提高SRC剪力墙的位移延性。给出了满足具体延性需求、对应各种轴压比情况下的SRC剪力墙边缘约束区箍筋最小配箍特征值。
In order to study the deformation capacity of steel reinforced concrete(SRC) shear walls,the yielding curvature and the ultimate curvature of SRC shear walls were established by equilibrium and deformation condition.On the basis of relationship between the curvature ductility ratio and the displacement ductility ratio,the displacement ductility ratio of SRC shear walls was calculated by numerical method.Then,the interrelated relationships among the displacement ductility ratio,the axial compression ratio,the characteristic value of stirrup content and the aspect ratio were obtained.The results show that increasing the characteristic value of stirrup content and limiting the axial compression ratio can improve displacement ductility.Minimum confinement ratio was proposed with various axial compression ratios and it is satisfied for the certain ductility demand.

引文

[1]PRIESTLEY M J N,KOWALSKY M J.Direct displacement-basedseismic design of concrete buildings[J].Bulletin of the New ZealandSociety for Earthquake Engineering,2000,33(4):421-444.
    [2]MEDHEKAR M S,KENNEDY D T L.Displacement-based seismicdesign of building-theory[J].Engineering Structures,2000,22(3):201-209.
    [3]PAULAY T.An estimation of displacement limits for ductile systems[J].Earthquake Engineering and Structural Dynamics,2002,31(3):583-599.
    [4]王志浩,钱稼茹.钢骨混凝土剪力墙的抗弯性能[J].建筑结构,1998,28(2):13-21.
    [5]钱稼茹,等.高轴压比钢骨混凝土剪力墙的抗震性能试验研究[J].建筑结构学报,2008,29(2):43-50.
    [6]吕西林,董宇光,丁子文.截面中部配置型钢的混凝土剪力墙抗震性能研究[J].地震工程与工程振动,2006,26(6):101-107.
    [7]SOON H C,BRYCE T,WILLIAM D C.Structural steel boundaryelements for ductile concrete walls[J].Journal of StructuralEngineering,ASCE,2004,130(5):763-768.
    [8]GB50010—2002混凝土结构设计规范[S].北京:中国建筑工业出版社,2002.
    [9]过镇海.钢筋混凝土原理和分析[M].北京:清华大学出版社,2003:183-188.
    [10]PAUIAY T,PRIESIEY M J N.Seismic Design of Reinforced Concreteand Masonry Buildings[M].New York:John Wiley&Sons,Inc,1992:86-88.