砂轮约束磨粒喷射精密光整加工机理及表面特性的研究
|
摘要
普通磨削由于磨削高温、反复碾压产生的工件表层材料过度变形、微裂纹、残余应力和表面层污染等，在工件上形成表面缺陷层，同时表面粗糙度和波纹度也较大。这将影响零件疲劳强度、抗蚀性和接触刚度等使用要求。重要零件需要在磨削后进行去除表面缺陷层、降低粗糙度和波纹度的微去除加工，但这增加了工序并需要特殊设备，给生产造成不便，增加了加工时间和生产成本。本文创新提出一种在磨床上进行的磨粒喷射精密光整加工新方法。该方法在磨削后停止砂轮切入进给，将磨料混合液注入磨削区，借助砂轮旋转和楔形区挤压流体的压力速度场使微细磨粒获得能量，实现对工件进行有边界约束的微去除加工。研究表明，该加工方法既保持或获得高的表面形状精度，又可以高效地获得具有粗糙度R_a0.15～1.6μm的无缺陷加工表面，实现高效、高精度、低粗糙度，并且磨削和抛光可以集成的表面精密光整加工。本文对砂轮约束磨粒喷射精密光整加工机理及表面特性进行了较系统的理论和实验研究，取得了若干有价值的研究成果。总结全文，本论文的工作包括如下几个方面：
(1)阐述了光整加工技术在机械制造中的作用，光整加工技术的分类、特点和发展方向，重点论述了游离磨粒精密光整加工技术的性能特点以及国内外发展方向，论述了本课题的背景及意义。
(2)根据Navier-Stokes方程和流体流动的连续性方程，建立了砂轮约束磨粒喷射精密光整加工中砂轮、工件楔形接触区流体动压力的三维数学模型并进行仿真研究，研究了楔形区流体动压力的分布规律及其影响因素。对砂轮与工件之间楔形区域形成的流体动压力进行了实验研究，实验结果表明，依据Navier-Stokes方程和流体流动的连续性方程建立的动压力理论模型与实验结果吻合，理论模型能很好的预测接触区流体压力场分布。
(3)建立了砂轮、工件楔形区流体速度场模型，研究了楔形区流体速度场的分布规律及其影响因素。研究了磨粒速度与磨料液流速度之间的关系。
(4)基于磨粒特征尺寸与砂轮、工件之间液膜厚度比值变化，研究了砂轮约束磨粒喷射精密光整加工材料去除机理，即：两体研磨加工，三体抛光加工，磨粒喷射加工，流体动压力剪切加工以及化学机械加工等加工模式的集成。分
The conventional grinding makes surface defects such as severely deformation,micro-crack, tensile residual stresses,surface layer pollution and ground burnout because of high grinding zone temperatures. At the same time,the machined surface roughness and ripple values are also bigger. Such more grinding defects, if not well diminished, would effect the ground surface fatigue strength, resistance corroding capacity and contact rigidity. Accordingly, more important parts require micro removal machining in order to reduce surface defects and diminish surface roughness and ripple. However, this can increase working procedures and extra equipment lead to increase costs.
According to above mention, author invent a newly abrasive jet precision finishing method, which inject slurry of abrasive and liquid solvent to grinding zone under haven't depth of cut infeed condition when accomplished workpiece grinding. The abrasive particles with grinding wheel as restraint are driven and energized by the rotating grinding wheel and liquid hydrodynamic pressure and increased slurry speed between grinding wheel and work surface achieved micro removal finishing process. The investigate showing,the micro removal machining with grinding wheel as restrain, not only to attain higher surface form accuracy but also to can acquire efficiently free defects finishing surface with R_a0.15~1.6μm and finally achieve high efficiency, high precision and low roughness values, furthermore, Integrating grinding process and polishing into one features, namely surface precision finishing. In the paper, the systematical research on the mechanism and surface characteristic of machined surface for abrasive jet finishing with grinding wheel as restraint by theoretical and experimental investigation and
(1)阐述了光整加工技术在机械制造中的作用，光整加工技术的分类、特点和发展方向，重点论述了游离磨粒精密光整加工技术的性能特点以及国内外发展方向，论述了本课题的背景及意义。
(2)根据Navier-Stokes方程和流体流动的连续性方程，建立了砂轮约束磨粒喷射精密光整加工中砂轮、工件楔形接触区流体动压力的三维数学模型并进行仿真研究，研究了楔形区流体动压力的分布规律及其影响因素。对砂轮与工件之间楔形区域形成的流体动压力进行了实验研究，实验结果表明，依据Navier-Stokes方程和流体流动的连续性方程建立的动压力理论模型与实验结果吻合，理论模型能很好的预测接触区流体压力场分布。
(3)建立了砂轮、工件楔形区流体速度场模型，研究了楔形区流体速度场的分布规律及其影响因素。研究了磨粒速度与磨料液流速度之间的关系。
(4)基于磨粒特征尺寸与砂轮、工件之间液膜厚度比值变化，研究了砂轮约束磨粒喷射精密光整加工材料去除机理，即：两体研磨加工，三体抛光加工，磨粒喷射加工，流体动压力剪切加工以及化学机械加工等加工模式的集成。分
The conventional grinding makes surface defects such as severely deformation,micro-crack, tensile residual stresses,surface layer pollution and ground burnout because of high grinding zone temperatures. At the same time,the machined surface roughness and ripple values are also bigger. Such more grinding defects, if not well diminished, would effect the ground surface fatigue strength, resistance corroding capacity and contact rigidity. Accordingly, more important parts require micro removal machining in order to reduce surface defects and diminish surface roughness and ripple. However, this can increase working procedures and extra equipment lead to increase costs.
According to above mention, author invent a newly abrasive jet precision finishing method, which inject slurry of abrasive and liquid solvent to grinding zone under haven't depth of cut infeed condition when accomplished workpiece grinding. The abrasive particles with grinding wheel as restraint are driven and energized by the rotating grinding wheel and liquid hydrodynamic pressure and increased slurry speed between grinding wheel and work surface achieved micro removal finishing process. The investigate showing,the micro removal machining with grinding wheel as restrain, not only to attain higher surface form accuracy but also to can acquire efficiently free defects finishing surface with R_a0.15~1.6μm and finally achieve high efficiency, high precision and low roughness values, furthermore, Integrating grinding process and polishing into one features, namely surface precision finishing. In the paper, the systematical research on the mechanism and surface characteristic of machined surface for abrasive jet finishing with grinding wheel as restraint by theoretical and experimental investigation and
引文
1.T.R. Loveless, R.Ewilliams.K. P. Rajurkar. A study of effects abrasive-flow finishing on various machined surfaces[J]. Journal of Materials Processing Technology 47(1994)133-151.
2. Rajendra,K.Jain.V.K.jain. Specific energy and temperature determination in abrasive flow machining process[J]. International Journal of Machine Tools & Manufacture 41(2000)1689-1704.
3. K. Suzuki, Development of a New Mechanochemical Polishing Method with a Polishing Film for Ceramic Round Bars[J], 1991, Annals of The CIRP, pp.339—342
4. Rajendra K.Jain.Vijay K.Jain,P.M.Dixit. Modeling of material removal and surface roughness in abrasive flow machining process[J]. International Journal of Machine Tools & Manufacture 39(1999)1903— 1923.
5.V.K.Jain,S.G.Adsul. Experimental investigations into abrasive flow machining[J]. International Journal of Machine Tools & Manufacture 40(2000)1003-1021.
6.Rajendra Kumar Jain, Vijay Kumar Jain. Optimum selection of machining conditions in abrasive flow machining using neural network[J]. Journal of Materials Processing Technology 108(2000)62—67.
7.G.Burkhard,F.Rehsteiner. High Efficiency Abrasive Tool for Honing[J], 2002, Annals of the CIRP, pp.323—327
8.C.J.Evans,E.paul,D.Dornfeld,D.A.Lucca,etc,Material Removal Mechanisms in Lapping and Polishing[J]. 2003, Annals of the CIRP,pp.128~149
9. M.R.Schumack,Jin-Bok Chung.W.W.Schuitz etc.Analysis of Flow Under a Grinding Wheel[J]. Transactions of the ASME 1991 MAY,VOL.113,190~ 197.
10.P.Hryniewicz, A.Z.Szeri. Application of Lubrication Theory to Fluid Flow in Grinding: Part I -Flow Between Smooth Surfaces[J]. Transactions of the ASME 2001 January,Vol. 123,94-100.
11.P.Hryniewicz, A.Z.Szeri. Application of Lubrication Theory to Fluid Flow in Grinding: Part II-Flow Between Smooth Surfaces[J]. Transactions of theASME 2001 January, Vol. 123, 101～107.
12. Chang Chong-Ching, An application of lubrication theory to predict useful flow-rate of coolants on grinding porous media[J]. Tribology International. Vol. 30. No. 8. pp. 575～581. 1997.
13 Bo Zhang, Akira Nakajima, Hydrodynamic Fluid Pressure in Grinding Zone During Grinding With Metal-Bonded Diamond Wheels[J]. Journal of Tribology. Vol. 122. No. 7. pp. 603～608. 2000.
14. F. Engineer, C. Guo, S. Malkin, Experimental Measurement of Fluid Flow Through the Grinding Zone[J]. Journal of Engineering for Industry. Vol. 114. No. 2. pp. 61～66. 1992.
15. C. Guo, S. Malkin, Analysis of Fluid Flow Through the Grinding Zone[J]. Journal of Engineering for Industry. Vol. 114. No. 11. pp. 427～434. 1992.
16. R. E. Williams, K. P. Rajurkar, Stochastic Modeling and Analysis of Abrasive Flow Machining[J]. Journal of Engineering for Industry. Vol. 114. No. 2. pp. 74～81. 1992.
17. E. S. Prakash, K. Sadashivappa, Vince Joseph, etc. Nonconventional cutting of plate glass using hot air jet experimental studies[J]. Mechatronics 11(2001)595～615.
18. Kazuto Yamauchi, Kikuji Hirose, Hidekazu Goto etc. First-principles simulations of removal process in EEM(Elastic Emission Machining)[J]. Computational Materials Science 14(1999) 232～235.
19．袁哲俊，王先逵．精密和超精密加工技术[M]．北京：机械工业出版社，1999
20．J．卡兹马莱科．切削、磨料及腐蚀加工原理[M]．北京：机械工业出版社，1985
21．王贵成，张银喜．精密与特种加工[M]．武汉：武汉理工大学出版社，2001
22. Jeong-Du Kim. Motion analysis of powder particles in EEM using cylindrical polyurethane wheel[J]. International Journal of Machine Tools & Manufacture 42(2002) 21～28.
23．杨世春．表面质量与光整技术[M]．北京：机械工业出版社，2000
24. N. Umehara, R. Komanduri. Magnetic fluid grinding of HIP-Si3N4 rollers[J]. Wear 192(1995): 85～93
25. Yaw-Terng Su, Shuh-Yi Wang, Ping-Yi Chao, et al. Investigation of elastic emission machining process: lubrication effects[J]. Precision Engineering 17: 164～172, 199526.Kazuto Yamauchi.Kikuji Hirose.Hidekazu, et al. First-principles simulations of removal process in EEM(Elastic Emission Machining) [J] Computational Materials Science 14 (1999) 232—235
27. Ibrahim M. Deiab, Mohamed A. Elbestawi. Experimental determination of the friction coefficient on the workpiece-fixture contact surface in workholding applications[J]. International Journal of Machine Tools &Manufacture 45 (2005) 705-712
28.Jeong-Du Kim. Motion analysis of powder particles in EEM using cylindrical polyurethane wheel[J]. International Journal of Machine Tools & Manufacture 42 (2002) 21-28
29.Rajendra K. Jain, V.K. Jain. Stochastic simulation of active grain density in abrasive flow machining[J]. Journal of Materials Processing Technology 152 (2004) 17-22
30.V.K. Jain, S.G. Adsul. Experimental investigations into abrasive flow machining[J], International Journal of Machine Tools & Manufacture 40 (2000) 1003-1021
31.Rajendra K. Jain, Vijay K. Jain. Modeling of material removal and surface roughness in abrasive flow machining process[J], International Journal of Machine Tools & Manufacture 39 (1999) 1903—1923
32.Hee-Won Jeong , Tetsuya Aoki, Takeshi Hatsuzawa. High-effiency fixed abrasive polishing method for quartz crystal blanks[J], International Journal of Machine Tools & Manufacture 44 (2004) 167—173
33.Dong-Sam Park, Myeong-Woo Cho, Honghee Lee. Micro-grooving of glass using micro-abrasive jet machining[J], Journal of Materials Processing Technology 146 (2004) 234—240
34.Kah Fai Leong, Chee Kai Chua, Gim Siong Chua. Abrasive jet deburring of jewellery models built by stereolithography apparatus (SLA) [J], Journal of Materials Processing Technology 83 (1998) 36—47
35.Y. Uehara, M. Wakuda, Y. Yamauchi. Tribological properties of dimpled silicon nitride under oil lubrication[J]. Journal of the European Ceramic Society 24 (2004) 369—373
36.Ming Chen, Koji Kato., Koshi Adachi. Friction and wear of self-mated SiC and Si3N4 sliding in water[J], Wear 250 (2001) 246—255
37. U. Dulias, L. Fang, K. -H. Zum Gahr. Effect of surface roughness of self-mated alumina on friction and wear in isooctane-lubricated reciprocating sliding contact[J], Wear 252(2002) 351～358
38. Maynard Smith, Dale E. Niesz. Chemical mechanical polishing(CMP) anisotropy in sapphire[J], Applied Surface Science 236(2004) 120～130
39. Krishna Rajan, Rajiv Singh, J. Adler. Surface interaction forces in chemical-mechanical planarization[J], Thin Solid Films 308-309(1997) 529～532
40. Yaw-Terng Su, Yui-Chen Kao. An experimental study on machining rate distribution of hydrodynamic polishing process[J], Wear 224 1999 95～105
41. C. J. Evans, E. Paul, D. Dornfeld, Material Removal Mechanisms in Lapping and Polishing[J], Annals of the CIRP, pp. 323～327
42．李长河，修世超，蔡光起．超硬磨料砂轮修锐技术最新进展[J]．工具技术，2005，39(3)：7～9
43 周桂如，流体润滑理论[M]，杭州：浙江大学出版社，1990
44．张鹏顺，弹性流体动力润滑及其应用[M]，北京：高等教育出版社，1995
45．温诗铸，弹性流体动力润滑[M]，北京：清华大学出版社，1992
46．巩亚东．超高速磨削砂轮气流场的基础研究[D]，东北大学博士学位论文，2004
47．陆君安，尚涛，谢进，偏微分方程的MATLAB解法[M]，武汉：武汉大学出版社，2001
48．John H．Mathews，Kurtis D．Fink．数值方法(MATLAB版)[M]，北京：电子工业出版社，2002
49．苏煜城，吴启光，偏微分方程数值解法[M]，北京：气象出版社，1989
50．周桂如，马骥，全永听，流体润滑理论[M]，杭州：浙江大学出版社，1987
51．梁冰，固液两相流泵的边界层理论及其应用[M]，北京：科学出版社，2003
52. P. Hryniewicz, A. Z. Szeri and S. Jahanmir. Application of Lubrication Theory to Fluid Flow in Grinding: Part Ⅰ—Flow Between Smooth Surfaces[J]. Transaction of the ASME, Vol. 123, 2001, 94～100.
53. Bo Zhang, Akira Nakajima. Hydrodynamic Fluid Pressure in Grinding Zone During Grinding With Metal-Bonded Diamond Wheels[J], Journal of Tribology, July 2000, Vol. 122, 603～608
54. P. Hryniewicz, A. Z. Szeri. Application of Lubrication Theory to Fluid Flow in Grinding: Part Ⅱ—Influence of Wheel and Workpiece Roughness[J],??Tribology JANUARY 2001, Vol. 123, 101～107
55. Jeong-Du Kim. Motion analysis of powder particles in EEM using cylindrical polyurethane wheel[J], International Journal of Machine Tools & Manufacture 42(2002) 21～28
56. Katsushi Furutani, Nguyen Trong Hieu, Noriyuki Ohgur. Automatic compensation for grinding wheel wear by pressure based in-process measurement in wet grinding[J], Precision Engineering 27(2003) 9～13
57. Katsushi Furutani, Noriyuki Ohguro, Nguyen Trong Hieu. In-process measurement of topography change of grinding wheel by using hydrodynamic pressure[J], International Journal of Machine Tools & Manufacture 42(2002) 1447～1453
58. S. Ebbrell, N. H. Woolley, Y. D. Tridimas. The effects of cutting fluid application methods on the grinding process[J], International Journal of Machine Tools & Manufacture 40(2000) 209～223
59. Sun-Kyu Lee, Yuji Miyamoto, Tsunemoto. E. ects of minimizing hydrodynamic pressure in ultra-precision mirror grinding[J], International Journal of Machine Tools & Manufacture 44(2004) 1031～1036
60. Mitjan Kalin, Said Jahanmir. Influence of roughness on wear transition in glass-infiltrated alumina[J], Wear 255(2003) 669～676
61．李长河，原所先，修世超，等．超高速磨削中的砂轮自动平衡技术[J]．新技术新工艺，2004，5：29～31
62. Jeong-Du Kim. Motion analysis of powder particles in EEM using cylindrical polyurethane wheel[J], International Journal of Machine Tools & Manufacture 42(2002) 21～28
63. Shun-bin Wang and Hong-Sen Kou. Cooling effectiveness of cutting fluid in creep feed grinding[J], Heat Transfer, Vol24 No. 6 pp. 771～783, 1997
64. K. Ramesh, S. H. Yeo, Z. W. Zhong. Coolant shoe development for high efficiency grinding[J], Journal Materials Processing Technology[J], 2004, 114(4): 240～245
65. Yaw-Terng Su), Yui-Chen Kao. An experimental study on machining rate distribution of hydrodynamic polishing process[J], Wear, 1999., 224(1): 95～105
66. Ravi Saxena, Dipto G. Thakurta, Ronald J. Gutmann. A feature scale model??for chemical mechanical planarization of damascene structures[J], Thin Solid Films 449(2004) 192～206
67. Sang-Shin Park, ChuI-Ho Cho, Yoomin Ahn. Hydrodynamic analysis of chemical mechanical polishing process[J], Tribology International 33(2000) 723～730
68. Yaw-Terng Su, Tu-Chieh Hung, Chuen-Chyi Horng. An experimental study on tool wear of hydrodynamic polishing process[J], Wear 246(2000) 117～129
69. Yaw-Terng Su, Tu-Chieh Hung, Chun-Cheng Weng. Ultra-precision machining by the cylindrical polishing process[J], International Journal of Machine Tools & Manufacture 43(2003) 1197～1207
70．李长河，蔡光起．游离磨粒精密光整加工方法的机理及关键技术[J]．机床制造产业，2005，6：7～18
71．李长河，修世超，蔡光起．微细游离磨粒借助流体动压力实现的超精密加工技术[J]．机械设计与制造，2005，12：72～75
72. Jongwon Seok, Cyriaque P. Sukam, Andrew T. Kim. Multiscale material removal modeling of chemical mechanical polishing[J], Wear 254(2003) 307～320
73. Sum Huan Ng. Pad Soaking Effect on Interfacial Fluid Pressure Measurements During CMP[J], Journal of Tribology, JULY 2003, Vol. 125: 582～586
74. Lei Shan, Joseph Levert. Interfacial Fluid Mechanics and Pressure Prediction in Chemical Mechanical Polishing[J], Journal of Tribology, JULY 2000, Vol. 122: 539～543
75. Chul-Ho Cho, Sang-Shin Park, Yoomin Ahn. Three-dimensional wafer scale hydrodynamic modeling for chemical mechanical polishing[J], Thin Solid Films 389, 2001. 254～260
76. W. Che, A. Chandra. Mechanistic Understanding of Material Detachment During Micro-Scale Polishing[J], Journal of Manufacturing Science and Engineering, NOVEMBER 2003, Vol. 125: 731～735
77. Rajendra K. Jain, Vijay K. Jain, P. M. Dixit. Modeling of material removal and surface roughness in abrasive flow machining process[J], International Journal of Machine Tools & Manufacture 39(1999) 1903～192378. L. B. Zhou, H. Eda, J. Shimizu. State-of-art technologies and kinematical analysis for one-stop finishing of φ300mm Si wafer[J], Journal of Materials Processing Technology, 2002, 129(1): 34～40
79. A. Tazibt, F. Parsy, N. Abriak. Theoretical analysis of the particle acceleration process in abrasive jet cutting[J], Computational Materials Science, 1996, 5: 243～354
80. Robert W. Lyczkowsk, Jacques X. Bouillard. State-of-the-art review of erosion modeling in fluid/solids systems[J], Progress in Energy and Combustion Science 28(2002) 543～602
81. P. H. Shipway. A mechanical model for particle motion in the micro-scale abrasion wear test[J], Wear 257(2004) 984～991
82. M. Talia, H. Lankarani, J. E. Talia. New experimental technique for the study and analysis of solid particle erosion mechanisms[J], Wear, 1999, 225(12): 1070～1077
83. Jae-Mo Lee, Won-Hyuk Jin, Dae-Eun Kim. Application of single asperity abrasion process for surface micro-machining[J], Wear 251(2001) 11331143
84. Rajendra K. Jain, V. K. Jain. Specific energy and temperature determination in abrasive flow machining process[J], International Journal of Machine Tools & Manufacture 41(2001) 1689～1704
85. Wook-Bae Kim, Byung-Kwon Min. Surface Finishing and Evaluation of Three-Dimensional Silicon Microchannel Using Magnetorheological Fluid[J], Journal of Manufacturing Science and Engineering, NOVEMBER 2004, Vol. 126: 772～778
86. William L. Cooper, Adrienne S. Lavine. Grinding Process Size Effect and Kinematics Numerical Analysis[J], Journal of Manufacturing Science and Engineering, FEBRUARY 2000, Vol. 122: 59～69
87. M. S. Bingley, S. Schnee. A study of the mechanisms of abrasive wear for ductile metals under wet and dry three-body conditions[J], Wear 258(2005) 50～61
88．李长河，修世超，李琦，等．磨料喷射光整加工机理及在机械领域中的应用[J]．机械制造，2004，8：18～21
89．李长河，原所先，李虎，等．磨削区内气流场速度和压力分布规律的研究进??展[J]．金刚石与磨料磨具工程，2004，3：31～34
90. C. H. Li, G. Q. Cai, S. C. Xiu. High efficiency abrasive machining process and its key technologies[J], The 11th international conference on industrial engineering and engineering management. 2005, 4: 516～519
91. W. Che, A-F. Bastawros. Mechanistic Understanding of Material Detachment During Micro-Scale Polishing[J], Journal of Manufacturing Science and Engineering, NOVEMBER 2003, Vol. 125: 731～735
92. Wook-Bae Kim, Sung-Jun Park, Byung-Kwon Min. Surface finishing technique for small parts using dielectrophoretic effects of abrasive particles[J], Journal of Materials Processing Technology 147(2004) 377～384
93. W. J. Zong, D. Li, K. Cheng, T. Sun. The material removal mechanism in mechanical lapping of diamond cutting tools[J], International Journal of Machine Tools & Manufacture 45(2005) 783～788
94. J. Kang, M. Hadfield. Examination of the material removal mechanisms during the lapping process of advanced ceramic rolling elements[J], Wear 258(2005) 2～12
95. S. W. Lee, Y. C. Lee, H. D. Jeong. The effect of high pressure air jet on form accuracy in slot grinding[J], Journal of Materials Processing Technology 128(2002) 67～72
96. B. Lauwers, J. P. Kruth, W. Liu, W. Investigation of material removal mechanisms in EDM of composite ceramic materials[J], Journal of Materials Processing Technology 149(2004) 347～352
97. Q. H. Zhang, J. H. Zhang, Z. X. Jia. Material-removal-rate analysis in the ultrasonic machining of engineering ceramics[J], Journal of Materials Processing Technology 88(1999) 180～184
98. P. S. Sreejith, B. K. A. Ngoi. Material removal mechanisms in precision machining of new materials[J], International Journal of Machine Tools & Manufacture 41(2001) 1831～1843
99．李长河 蔡光起 李琦．砂轮约束磨粒喷射精密光整加工表面形貌创成机理研究[J]．东北大学学报(自然科学版)，2005，23(6)：581—585
100. Williams, J. A., and Hyncica, A. M.,. Mechanisms of Abrasive Wear in Lubricated Contacts. Wear[J], 1992, 152, pp. 57～74.101．赵恒华，蔡光起，超高速磨削冲击成屑的建模和机理研究[J]，中国机械工程，v 15，n 12，Jun 25，2004，p 1038～1041
102. Ronen, A., and Malkin, S.. Wear Mechanisms of Statically Loaded Hydrodynamic Bearings by Contaminant Abrasive Particles[J], Wear,, 1981, 68, pp. 371～389.
103. Buijs, M., and Korpel-van Houten, K.. Three-Body Abrasion of Brittle Materials as Studied by Lapping[J]. Wear, 1993, 166, pp. 237～245.
104．赵恒华，蔡光起，李长河，等．高效深磨中磨削温度和表面烧伤研究[J]，中国机械工程，V 15，n 22，2004，p 2048～2052
105. Y. P. Chang, M. Hanshimura and D. A. Dornfeld. An Investigation of Material Removal Mechanisms in Lapping With Grain Size Transition[J]. Journal of Manufacturing Science and Engineering, 2000, Vol. 122, 413～419.
106. K. Bose, R. J. K. Wood. Influence of load and speed on rolling micro-abrasion of CVD diamond and other hard coatings[J], Diamond and Related Materials 12(2003) 753～756
107. K. BARCOVA, M. MASHLAN and P. MARTINEC. Mossbauer Study of the Thermal Behaviour of Garnets Used in High-Energy Water Jet Technologies[J], Hyperfine Interactions 139/140: 463～469, 2002.
108. M. A. Verpui, G. de With, P. G. Th. Bed thickness and particle size distribution in three body abrasion[J], Wear 188(1995) 102～107
109. P. H. Shipway. The role of test conditions on the microabrasive wear behaviour of soda-lime glass[J], Wear 233-235 1999 191～199
110. Yuan-Zhong Hu, Dong Zhu. A Full Numerical Solution to the Mixed Lubrication in Point Contacts, Journal of Tribology[J], JANUARY 2000, Vol. 122: 1～9
111. P. I. YASCHERITSIN AND L. E. SERGEEV, The Comparative Appraisal of Quality Characteristics of Holes after Different Finishing Methods[J], Advanced Performance Materials 4, 337～347(1997)
112. M. A. Verspui, G. de With, A. Corbijn. Simulation model for the erosion of brittle materials[J], Wear 233-235 1999 436～443
113 修世超，李长河，蔡光起．磨削加工表面粗糙度理论模型修正方法[J]，东北大学学报(自然科学版)，2005，26(8)：770—774
114 臼井英治．切削磨削加工学[M]．高希正，译．北京：机械工业出版社，1982，482??—492.
115. Yaw-Terng Su, Chuen-Chyi Horng,Yeong-Dong Hwang. Effects of tool surface irregularities on machining rate of a hydrodynamic polishing process[J], Wear, 1996, 199(1): 89～99
116. T. R. Loveless, R. E. Williams, K. P. Rajurkar. A study of the effects of abrasive-flow finishing on various machined surfaces[J], Journal of Materials Processing Technology, 1994, 47(1): 133～151
117. Rajendra K. Jain, Vijay K. Jain*, P. M. Dixit. Modeling of material removal and surface roughness in abrasive flow machining process[J], International Journal of Machine Tools & Manufacture, 1999, 39(12): 1903～1923
118. Rajendr K. Jain, V. K. Jain. Stochastic simulation of active grain density in abrasive flow machining[J], Journal of Materials Processing Technology, 2004, 152(1): 17～22
119. V. K. Jain *, S. G. Adsul. Experimental investigations into abrasive flow machining(AFM)[J], International Journal of Machine Tools & Manufacture2000, 40(10): 1003～1021
120. Jeong-Du Kim, Min-Seog Choi. Simulation for the prediction of surface-accuracy in magnetic abrasive machining[J], Journal of Materials Processing Technology, 1995, 53(6): 630～642
121. Sunil Jha, V. K. Jain_ Design and development of the magnetorheological abrasive flow finishing(MRAFF) process[J], International Journal of Machine Tools & Manufacture, 2004, 44(10): 1019～1029
122. Hee-Won Jeong, Tetsuya Aoki, Takeshi Hatsuzawa. High-efficiency fixed abrasive polishing method for quartz crystal blanks[J], International Journal of Machine Tools & Manufacture 44(2004) 167～173
123. Ravi Saxena, Dipto G. Thakurta, Ronald J. Gutmann. A feature scale model for chemical mechanical planarization of damascene structures[J], Thin Solid Films 449(2004) 192～206
124. Jongwon Seok, Cyriaque P. Sukam, Andrew T. Kim. Material removal model for chemical-mechanical polishing considering wafer flexibility and edge effects[J], Wear 257(2004) 496～508
125．李长河，蔡光起，李琦，等．砂轮约束磨粒喷射精密光整加工材料去除机理研究[J]．中国机械工程，2005，16(23)：2116～2120126. Chul-Ho Cho, Sang-Shin Park, Yoomin Ahn. Three-dimensional wafer scale hydrodynamic modeling for chemical mechanical polishing[J], Thin Solid Films 389Z2001. 254～260
127. T. Mori, K. Hirota, Y. Kawashima. Clarification of magnetic abrasive finishing mechanism[J], Journal of Materials Processing Technology 143-144(2003) 682～686
128. N. Umehara, R. Komanduri. Magnetic fluid grinding of HIP-Si_3N_4 rollers[J], Wear, 1996, 192(1): 85～93
129. Dhirendr K. Singhl, V. K. Jain, V. Raghuram. Parametric study of magnetic abrasive finishing process[J], Journal of Materials Processing Technology 149(2004) 22～29
130. I. Zarudi, L. C. Zhang. On the Limit of Surface Integrity of Alumina by Ductile-Mode Grinding[J], Journal of Engineering Materials and Technology, 2000, 122(3): 129～134
131. S. Wan, G. C. Lim. Transient Flow in Abrasive Suspension Jet Cutting Machines on Pump Shutdown[J], Journal of Manufacturing Science and Engineering, 2003, 125(2): 172～178
132．李长河，孙奕澎，蔡光起．自由磨粒复杂曲面磁力研磨光整加工试验研究[J]．制造技术与机床，2005，5：72～75
133. [1] Y. P. Chang, M. Hanshimura and D.A.Dornfeld. An Investigation of Material Removal Mechanisms in Lapping With Grain Size Transition[J]. Journal of Manufacturing Science and Engineering, 2000, Vol. 122, 413～419.
134. Buijs, M., and Korpel-van Houten, K.. Three-Body Abrasion of Brittle Materials as Studied by Lapping[J]. Wear, 1993, 166, pp. 237～245.
135. R. Chauhan, Y. Ahn, S. Chandrasekar, et al. Role of Indentation fracture in free abrasive machining of ceramics. Wear, 162-164(1993) 246～257.
136. M. Buils, K. Korpel and Van Houten. A model for lapping of glass[J], Journal of Materials Science 28(1993) 3014～3020.
137. L. Fang, L. Kong, J. Y. Su. Movement patterns of abrasive particles in three body abrasion[J], Wear, 162-164(1993) 782～789.
138. Sunil Jha, V. K. Jain. Design and development of the magnetorheological abrasive flow finishing(MRAFF) process[J], International Journal of Machine??Tools & Manufacture, 2004, 44(10): 1019～1029
139. Rajendra K. Jain, V. K. Jain. Stochastic simulation of active grain density in abrasive flow machining[J], Journal of Materials Processing Technology, 2004, 152(1): 17～22
140. Rajendra K. Jain, V. K. Jain. Specific energy and temperature determination in abrasive flow machining process[J], International Journal of Machine Tools & Manufacture, 2001, 41(12) 1689～1704
141. V. K. Jain, S. G. Adsul. Experimental investigations into abrasive flow machining(AFM)[J], International Journal of Machine Tools & Manufacture, 2000, 40(9): 1003～1021
142. Baogui Shi, J. L. Sullivan, M. A. Wild. Study of Generation Mechanism of Three-Body Particles in LinearTape Recording[J], Journal of Tribology, 2005, 127(2): 155～163
143. M. A. Verspui, G. De With, P. G. Th. Bed thickness and particle size distribution in three-body abrasion[J], Wear, 1995, 188(2): 102～107
144. R. I. Trezona, D. N. Allsopp, I. M. Hutchings. Transitions between two-body and three-body abrasive wear: influence of test conditions in the microscale abrasive wear test[J], Wear, 1999, 225(6):. 205～214
145. J. D. Gates. Two-body and three-body abrasion: A critical discussion[J], Wear, 1998, 214(2): 139～146
146．李长河，蔡光起，原所先．砂轮约束磨粒喷射精密光整加工材料去除模型[J]．农业机械学报，2005，36(11)：132～135
147. M. Bhagavat, V. Prasad, I. Kao. Elasto-Hydrodynamic Interaction in the Free Abrasive Wafer Slicing Using a Wiresaw: Modeling and Finite Element Analysis[J], Journal of Tribology, 2000, 122(4): 394～404
148. P. H. Shipway. The role of test conditions on the microabrasive wear behaviour of soda-lime glass[J], Wear, 1999, 233(3): 191～199
149. Yeong Yan Guu. Correlation between three-body wear and tribological characteristics of titanium nitride, titanium carbonitride and titanium carbide coatings[J], Wear, 1997, 208(3): 147～154
150. K. Bose, R. J. K. Wood. Influence of load and speed on rolling micro-abrasion of CVD diamond and other hard coatings[J], Diamond and Related Materials, 2003, 12(9): 753～756151.O.P. Modi_, B.K. Prasad, A.K. Jha, Low-stress abrasive wear behaviour of a 0.2% C steel: influence of microstructure and test parameters[J], Tribology Letters, 2003,15(3):249—255
152.Y. Ueharaa, M. Wakudab, Y. Yamauchic, Tribological properties of dimpled silicon nitride under oil lubrication[J], Journal of the European Ceramic Society,2004,24 (5) :369—373
153.Ming Chen, Koji Kato, Koshi Adachi. Friction and wear of self-mated SiC and Si3N4 sliding in water[J], Wear,2001, 250 (5): 246-255
154.Kah Fai Leong, Chee Kai Chua, Gim Siong Chua. Abrasive jet deburring of jewellery models built by stereolithography apparatus (SLA)[J], Journal of Materials Processing Technology ,1998,83 (1): 36—47
155.Mohammad Reza Baghbanan, Akihiro Yabuki, Roland S. Tribological behavior of aluminum alloys in a vibratory finishing process[J], Wear ,2003,255 (10): 1369-1379
156.Mitjan Kalin, Said Jahanmir. Influence of roughness on wear transition in glass-infiltrated alumina[J], Wear ,2003,255(7):669~676
157.U. Dulias, L. Fangb, K.-H. Zum Gahr. Effect of surface roughness of self-mated alumina on friction and wear in isooctane-lubricated reciprocating sliding contact[J], Wear, 2002,252 (7) :351~358
158.H.H. Tsai, H. Hocheng. Prediction of a thermally induced concave ground surface of the workpiece in surface grinding[J], Journal of Materials Processing Technology, 2002,122 (4): 148—159
159.Y.P.Chang, M.Hanshimura and D.A.Dornfeld. An Investigation of Material Removal Mechanisms in Lapping With Grain Size Transition[J]. Journal of Manufacturing Science and Engineering, 2000, Vol.122, 413—419.
160.Buijs, M., and Korpel-van Houten, K.Three-Body Abrasion of Brittle Materials as Studied by Lapping[J]. Wear, 1993, 166, pp. 237—245.
161.R. Chauhan, Y. Ahn, S.Chandrasekar.et al. Role of Indentation fracture in free abrasive machining of ceramics[J]. Wear, 162-164 (1993) 246—257.
162.Yutaka Hasegawa.Sasuke Miyazima. Polishing rate for (100) and (110) surfaces[J], Physical A, 1996,233(8):663—671
163.Ming Jiang, Nelson O. On chemo-mechanical polishing(CMP) of silicon nitride (Si_3N_4) workmaterial with various abrasives [J], Wear, 1998,220(1): 59～71
164. C. H. Li, G. Q. Cai, S. C. Xiu. Material Removal Model and Experimental Verification for Abrasive Jet Precision Finishing with Wheel as Restraint[J], Key Engineering Materials, 2006. Vol. 304-305: 555～559
165. Yaw-Terng Su, Yui-Chen Kao. An experimental study on machining rate distribution of hydrodynamic polishing process[J], Wear, 1999, 224(3): 95～105
166. Jongwon Seok, Cyriaque P. Sukam, Andrew T. Kim. Material removal model for chemical-mechanical polishing considering wafer flexibility and edge effects[J], Wear, 2004, 257(8): 496～508
167．李伯奎，刘远伟．表面粗糙度理论发展研究[J]，2004，38(4)：63～67
168．梁嵘，李达成，曹芒．表面微观形貌测量及其参数评定的发展趋势[J]，光学技术，1998，6：66～68
169．李丽伟，董申，程凯．表面微观形貌定量表征中几种新方法的应用[J]，中国机械工程，2002，13(19)：1702～1705
170．陈艺，岳梅，焦明华．采用计算机数据处理的表面形貌分析方法及应用[J]，淮南矿业学院学报，1995，15(3)：60～63
171．李伯奎．传统机械加工表面形貌评定的缺陷及发展方向[J]，淮阴工学院学报，2002，11(3)：63～65
172．李成贵．粗糙表面轮廓相关性的倒谱分析[J]，机械工程学报，2004，40(5)：87～91
173．蒋庄德，王海容，陈伟．分数布朗运动应用于机械加工表面形貌的评定[J]，现代计量测试，1997，6：15～19
174．李长河，蔡光起，刘枫．砂轮约束磨粒喷射精密光整加工工艺特性研究[J]．金刚石与磨料磨具工程，2005，5：26～29
175．汪慰军，吴昭同，陈历喜．基于分形的表面形貌特征描述与评定参数的研究[J]，计量学报，1998，19(2)：147～151
176．王飞，罗志增．基于功率谱的表面EMG信号运动模式识别[J]，杭州电子科技大学学报，2005，25(2)：37～40
177．金鑫，张之敬．基于制造特性的微小型构件表面形貌数值模型[J]，北京理工大学学报，2005，25(3)：189～193
178．葛世荣，陈国安．磨合表面形貌变化的特征粗糙度参数表征[J]，中国矿业大学学报，1999，28(3)：204～208179．马争，桂长林．评定磨合表面的最佳形貌参数[J]，摩擦学学报，1995，1995，15(4)：133～137
180．刘晓军，肖少军，谢铁邦．曲面表面粗糙度、波度及形状误差综合测量与分析的研究[J]，1997，31(3)：33～36
181．李成贵，董申．三维表面微观形貌的表征参数和方法[J]，宇航计测技术，1999，19(6)：33～32
182．李长河，修世超，蔡光起．高速超高速磨削工艺及其实现技术[J]．金刚石与磨料磨具工程，2004，4：16～20
183．李成贵，马小丽，袁长良．三维加工表面形貌等方性评定的研究[J]，太原工业大学学报，1996，27(1)：13～19
184．张滢，王维．虚拟数控车削表面形貌的仿真与表面粗糙度预测[J]，现代制造工程，2005，7：24～26
185．于思远，林彬，林滨．工程陶瓷超精密磨削表面质量的研究[J]，金刚石与磨料磨具工程，2002，5：12～19
186．周锦进，翟小兵，庞桂兵．脉冲电化学光整加工表面微观形貌的研究[J]，农业机械学报，2004，35(3)：150～153
187．蒋书文，姜斌，李燕．磨损表面形貌的三维分形维数计算[J]，摩擦学学报，2003，23(6)：433～436
188．王安良，杨春信．评价机械加工表面形貌的小波变换方法[J]，机械工程学报，2001，37(8)：65～70
189．梁洁，李尚平．用STM对高速磨削表面微观形貌的研究[J]，金刚石与磨料磨具工程，2001，3：7～10
190. D. Arola, M. Ramulu. Material removal in abrasive waterjet machining of metals surface integrity and texture[J], Wear, 1997, 210(6): 50～58
191. S. Paul, A. M. Hoogstrate, C. A. van Luttervelt. Analytical and experimental modelling of the abrasive water jet cutting of ductile materials[J], Journal of Materials Processing Technology, 1998, 73(3): 189～199
192. F. L. Chen, J. Wang, E. Lemma. Striation formation mechanisms on the jet cutting surface[J], Journal of Materials Processing Technology, 2003, 141(4): 213～218
193. Y. Uehara, M. Wakuda, Y. Yamauchi. Tribological properties of dimpled silicon nitride under oil lubrication[J], Journal of the European Ceramic Society, 2004, 24(5): 369～373194. M. Kantha Babu, O. V. Krishnaiah Chetty. A study on recycling of abrasives in abrasive water jet machining[J], Wear, 2003, 254(9): 763～773
195．周熙熙，阎秋生．磨料喷射加工加工特性研究[J]，机械研究与应用，2003，16(3)：30～32
196. Keyurkumar, J. Patel. Quantitative evaluation of abrasive contamination in ductile material during abrasive water jet machining and minimizing with a nozzle head oscillation technique[J], International Journal of Machine Tools & Manufacture, 2004, 44(6): 1125～1132
197. R. Balasubbramaniam, J. Krishnan, N. Ramakrishnan. Astudy on the shape of the surface generated by abrasive jet machining[J], Journal of Materials Processing Technology, 2002, 121(1): 102～106
198. A. Jourani, M. Dursapt, H. Hamdi. Effect of the belt grinding on the surface texture: Modeling of the contact and abrasive wear[J], Wear, 2005, 259(11): 1137～1143
199. Jeong-Du Kim, Min-Seong Choi. Simulation for the prediction of surface-accuracy in magnetic abrasive machining[J], Journal of Materials Processing Technology, 1995, 53(6): 630～642
200. T. K. Puthanangady, S. Malkin. Experimental investigation of the superfinishing process[J], Wear, 1995, 185(2): 173～182
201．李长河，蔡光起，修世超．低温冷却磨削机理研究[J]．金刚石与磨料磨具工程，2006，1：17～20
202．田欣利，于爱兵，林彬．陶瓷磨削残余应力对表面性能的影响[J]，机械科学与技术，2002，21(4)：615～617
203．刘菊东，王贵成，陈康敏，等．非淬硬钢磨削表面硬化层的试验研究[J]，中国机械工程，2005，16(11)：1013～1017
204．杨斌久，盖全芳，张玉峰．高速磨削加工的残余硬度[J]，长春工业大学学报(自然科学版)，2004，25(1)：41～43
205．冯宝富，马春容．淬硬轴承钢磨削后的表面硬度[J]，辽宁石油化工大学学报，2005，25(2)：41～44
206．王宗英，肖楠，吕淑萍．40Cr钢表面改性处理及磨损性能研究[J]，沈阳建筑大学学报(自然科学版)，2005，21(3)：281～284
207．李长河，赵亮，蔡光起．利用磨削热进行表面热处理的新工艺技术研究[J]．2005，1：61—64208．刘菊东，王贵成，陈康敏．65Mn钢磨削硬化层组织的研究[J]，中国机械工程，2004，15(17)：1073～1076
209．邓守军，孙乐民，李占君．PCrMo钢的摩擦磨损特性实验研究[J]，润滑与密封，2005，4：84～85
210．孙月海，张新，郑惠江．蜗杆传动用摩擦副材料在滑动干摩擦条件下的摩擦磨损性能研究[J]，摩擦学报，2005，25(3)：279～282
211．常海波，徐洮，李红轩．用等离子体增强化学气相沉积技术制备类金刚石碳薄膜的摩擦磨损性能研究[J]，摩擦学学报，2005，25(4)：298～302
212．杨卓娟，韩志武，任露泉．激光处理凹坑形仿生非光滑表面试件的高温摩擦磨损特性研究[J]，摩擦学学报，2005，25(4)：374～378
213．张永振，邱明，上官宝．高速干摩擦条件下铝基复合材料的摩擦磨损行为研究[J]，摩擦学学报，2005，25(4)：343～347
214．李长河，蔡光起．超高速磨削技术的特点及在工业中的具体应用[J]．通用机械，2005，7：69～72
215．王振廷，陈华辉．碳化钨颗粒增强金属基复合材料涂层组织及其摩擦磨损性能[J]，摩擦学学报，2005，25(3)：204～207
216．徐桂芳，程晓农，司乃潮．不同磨损介质下铜锌铝形状记忆合金滚动磨损性能与磨损机制研究[J]，新技术新工艺，2004，8：46～49
217．邢建东，高义民，张国赏．不锈钢与高碳钢的冲刷腐蚀磨损试验研究[J]，西安交通大学学报，2004，38(5)：469～473
218．丁厚福，崔方明，杜晓东．成分和组织对衬板钢在腐蚀料浆环境下的冲击磨损性能与机理的影响[J]，摩擦学学报，摩擦学学报，2005，25(4)：222～225
219．郭亮，丁厚福，严小冲．低碳高合金钢和高锰钢冲击腐蚀磨损特性研究[J]，兵器材料科学与工程，2005，28(2)：12～16
220．丁厚福，崔方明，杜晓东．腐蚀条件下冲击功对钢冲击磨损性能与机制的影响[J]，材料热处理学报，2004，26(2)：55～61
221．李先芬，苏勇，陈翌庆．两种钢冲击腐蚀磨损性能的试验研究[J]，兵器材料科学与工程，2003，26(3)：18～21
222．王安东，戴起勋．生物医用材料316L不锈钢的磨损腐蚀特性研究[J]，金属热处理，2005，30(3)：33～36
223．张慧君．自相关函数在机械故障分析中应用[J]，机械工艺师，2001，8：19～20
224．陈历喜．用随机分析的方法研究电加工表面形貌[J]，航空工艺技术，1995，2：??15～19
225．李西琴，陈历喜，汪慰军．用互相关函数判别零件表面形貌的特征[J]，机械科学与技术，1998，17(1)：49～51
226．邢彦锋，张明，侯仰海．电化学机械光整加工表面相关性分析[J]，山东理工大学学报：自然科学版，2003，17(3)：23～26
227．车建明．炭纤维增强铜基复合材料摩擦磨损性能同其磨损表面形貌相关性研究[J]，摩擦学学报，摩擦学学报，2004，24(2)：144～147
228．李惠芬，蒋向前，李柱．三维表面形貌的功能评定方法[J]，宇航计测技术，2001，21(6)：19～26
229．郝达兵，姜岩峰，黄庆安．各向异性腐蚀表面粗糙度的“应力模型”[J]，光电子技术，2003，23(3)：202～206
230．沈卫星，徐德衍．强激光光学元件表面功率谱密度函数估计[J]，强激光与粒子束，2000，12(4)：392～396
231．苑伟政，马炳和，李小莹．硅的准分子激光直写刻蚀微细加工特性研究[J]，机械工程学报，2000，36(3)：107～110
232. T. A. STOLARSKI. Attrition of silicon nitride as a function of counterface material and contact zone kinematics[J], JOURNAL OF MATERIALS SCIENCE 36(2001) 1911～1919
233. H. JOHANSEN, G. KASTNER. Surface quality and laser-damage behaviour of chemo-mechanically polished CaF2 single crystals characterized by scanning electron microscopy[J], JOURNAL OF MATERIALS SCIENCE 33(1998) 3839～384
2. Rajendra,K.Jain.V.K.jain. Specific energy and temperature determination in abrasive flow machining process[J]. International Journal of Machine Tools & Manufacture 41(2000)1689-1704.
3. K. Suzuki, Development of a New Mechanochemical Polishing Method with a Polishing Film for Ceramic Round Bars[J], 1991, Annals of The CIRP, pp.339—342
4. Rajendra K.Jain.Vijay K.Jain,P.M.Dixit. Modeling of material removal and surface roughness in abrasive flow machining process[J]. International Journal of Machine Tools & Manufacture 39(1999)1903— 1923.
5.V.K.Jain,S.G.Adsul. Experimental investigations into abrasive flow machining[J]. International Journal of Machine Tools & Manufacture 40(2000)1003-1021.
6.Rajendra Kumar Jain, Vijay Kumar Jain. Optimum selection of machining conditions in abrasive flow machining using neural network[J]. Journal of Materials Processing Technology 108(2000)62—67.
7.G.Burkhard,F.Rehsteiner. High Efficiency Abrasive Tool for Honing[J], 2002, Annals of the CIRP, pp.323—327
8.C.J.Evans,E.paul,D.Dornfeld,D.A.Lucca,etc,Material Removal Mechanisms in Lapping and Polishing[J]. 2003, Annals of the CIRP,pp.128~149
9. M.R.Schumack,Jin-Bok Chung.W.W.Schuitz etc.Analysis of Flow Under a Grinding Wheel[J]. Transactions of the ASME 1991 MAY,VOL.113,190~ 197.
10.P.Hryniewicz, A.Z.Szeri. Application of Lubrication Theory to Fluid Flow in Grinding: Part I -Flow Between Smooth Surfaces[J]. Transactions of the ASME 2001 January,Vol. 123,94-100.
11.P.Hryniewicz, A.Z.Szeri. Application of Lubrication Theory to Fluid Flow in Grinding: Part II-Flow Between Smooth Surfaces[J]. Transactions of theASME 2001 January, Vol. 123, 101～107.
12. Chang Chong-Ching, An application of lubrication theory to predict useful flow-rate of coolants on grinding porous media[J]. Tribology International. Vol. 30. No. 8. pp. 575～581. 1997.
13 Bo Zhang, Akira Nakajima, Hydrodynamic Fluid Pressure in Grinding Zone During Grinding With Metal-Bonded Diamond Wheels[J]. Journal of Tribology. Vol. 122. No. 7. pp. 603～608. 2000.
14. F. Engineer, C. Guo, S. Malkin, Experimental Measurement of Fluid Flow Through the Grinding Zone[J]. Journal of Engineering for Industry. Vol. 114. No. 2. pp. 61～66. 1992.
15. C. Guo, S. Malkin, Analysis of Fluid Flow Through the Grinding Zone[J]. Journal of Engineering for Industry. Vol. 114. No. 11. pp. 427～434. 1992.
16. R. E. Williams, K. P. Rajurkar, Stochastic Modeling and Analysis of Abrasive Flow Machining[J]. Journal of Engineering for Industry. Vol. 114. No. 2. pp. 74～81. 1992.
17. E. S. Prakash, K. Sadashivappa, Vince Joseph, etc. Nonconventional cutting of plate glass using hot air jet experimental studies[J]. Mechatronics 11(2001)595～615.
18. Kazuto Yamauchi, Kikuji Hirose, Hidekazu Goto etc. First-principles simulations of removal process in EEM(Elastic Emission Machining)[J]. Computational Materials Science 14(1999) 232～235.
19．袁哲俊，王先逵．精密和超精密加工技术[M]．北京：机械工业出版社，1999
20．J．卡兹马莱科．切削、磨料及腐蚀加工原理[M]．北京：机械工业出版社，1985
21．王贵成，张银喜．精密与特种加工[M]．武汉：武汉理工大学出版社，2001
22. Jeong-Du Kim. Motion analysis of powder particles in EEM using cylindrical polyurethane wheel[J]. International Journal of Machine Tools & Manufacture 42(2002) 21～28.
23．杨世春．表面质量与光整技术[M]．北京：机械工业出版社，2000
24. N. Umehara, R. Komanduri. Magnetic fluid grinding of HIP-Si3N4 rollers[J]. Wear 192(1995): 85～93
25. Yaw-Terng Su, Shuh-Yi Wang, Ping-Yi Chao, et al. Investigation of elastic emission machining process: lubrication effects[J]. Precision Engineering 17: 164～172, 199526.Kazuto Yamauchi.Kikuji Hirose.Hidekazu, et al. First-principles simulations of removal process in EEM(Elastic Emission Machining) [J] Computational Materials Science 14 (1999) 232—235
27. Ibrahim M. Deiab, Mohamed A. Elbestawi. Experimental determination of the friction coefficient on the workpiece-fixture contact surface in workholding applications[J]. International Journal of Machine Tools &Manufacture 45 (2005) 705-712
28.Jeong-Du Kim. Motion analysis of powder particles in EEM using cylindrical polyurethane wheel[J]. International Journal of Machine Tools & Manufacture 42 (2002) 21-28
29.Rajendra K. Jain, V.K. Jain. Stochastic simulation of active grain density in abrasive flow machining[J]. Journal of Materials Processing Technology 152 (2004) 17-22
30.V.K. Jain, S.G. Adsul. Experimental investigations into abrasive flow machining[J], International Journal of Machine Tools & Manufacture 40 (2000) 1003-1021
31.Rajendra K. Jain, Vijay K. Jain. Modeling of material removal and surface roughness in abrasive flow machining process[J], International Journal of Machine Tools & Manufacture 39 (1999) 1903—1923
32.Hee-Won Jeong , Tetsuya Aoki, Takeshi Hatsuzawa. High-effiency fixed abrasive polishing method for quartz crystal blanks[J], International Journal of Machine Tools & Manufacture 44 (2004) 167—173
33.Dong-Sam Park, Myeong-Woo Cho, Honghee Lee. Micro-grooving of glass using micro-abrasive jet machining[J], Journal of Materials Processing Technology 146 (2004) 234—240
34.Kah Fai Leong, Chee Kai Chua, Gim Siong Chua. Abrasive jet deburring of jewellery models built by stereolithography apparatus (SLA) [J], Journal of Materials Processing Technology 83 (1998) 36—47
35.Y. Uehara, M. Wakuda, Y. Yamauchi. Tribological properties of dimpled silicon nitride under oil lubrication[J]. Journal of the European Ceramic Society 24 (2004) 369—373
36.Ming Chen, Koji Kato., Koshi Adachi. Friction and wear of self-mated SiC and Si3N4 sliding in water[J], Wear 250 (2001) 246—255
37. U. Dulias, L. Fang, K. -H. Zum Gahr. Effect of surface roughness of self-mated alumina on friction and wear in isooctane-lubricated reciprocating sliding contact[J], Wear 252(2002) 351～358
38. Maynard Smith, Dale E. Niesz. Chemical mechanical polishing(CMP) anisotropy in sapphire[J], Applied Surface Science 236(2004) 120～130
39. Krishna Rajan, Rajiv Singh, J. Adler. Surface interaction forces in chemical-mechanical planarization[J], Thin Solid Films 308-309(1997) 529～532
40. Yaw-Terng Su, Yui-Chen Kao. An experimental study on machining rate distribution of hydrodynamic polishing process[J], Wear 224 1999 95～105
41. C. J. Evans, E. Paul, D. Dornfeld, Material Removal Mechanisms in Lapping and Polishing[J], Annals of the CIRP, pp. 323～327
42．李长河，修世超，蔡光起．超硬磨料砂轮修锐技术最新进展[J]．工具技术，2005，39(3)：7～9
43 周桂如，流体润滑理论[M]，杭州：浙江大学出版社，1990
44．张鹏顺，弹性流体动力润滑及其应用[M]，北京：高等教育出版社，1995
45．温诗铸，弹性流体动力润滑[M]，北京：清华大学出版社，1992
46．巩亚东．超高速磨削砂轮气流场的基础研究[D]，东北大学博士学位论文，2004
47．陆君安，尚涛，谢进，偏微分方程的MATLAB解法[M]，武汉：武汉大学出版社，2001
48．John H．Mathews，Kurtis D．Fink．数值方法(MATLAB版)[M]，北京：电子工业出版社，2002
49．苏煜城，吴启光，偏微分方程数值解法[M]，北京：气象出版社，1989
50．周桂如，马骥，全永听，流体润滑理论[M]，杭州：浙江大学出版社，1987
51．梁冰，固液两相流泵的边界层理论及其应用[M]，北京：科学出版社，2003
52. P. Hryniewicz, A. Z. Szeri and S. Jahanmir. Application of Lubrication Theory to Fluid Flow in Grinding: Part Ⅰ—Flow Between Smooth Surfaces[J]. Transaction of the ASME, Vol. 123, 2001, 94～100.
53. Bo Zhang, Akira Nakajima. Hydrodynamic Fluid Pressure in Grinding Zone During Grinding With Metal-Bonded Diamond Wheels[J], Journal of Tribology, July 2000, Vol. 122, 603～608
54. P. Hryniewicz, A. Z. Szeri. Application of Lubrication Theory to Fluid Flow in Grinding: Part Ⅱ—Influence of Wheel and Workpiece Roughness[J],??Tribology JANUARY 2001, Vol. 123, 101～107
55. Jeong-Du Kim. Motion analysis of powder particles in EEM using cylindrical polyurethane wheel[J], International Journal of Machine Tools & Manufacture 42(2002) 21～28
56. Katsushi Furutani, Nguyen Trong Hieu, Noriyuki Ohgur. Automatic compensation for grinding wheel wear by pressure based in-process measurement in wet grinding[J], Precision Engineering 27(2003) 9～13
57. Katsushi Furutani, Noriyuki Ohguro, Nguyen Trong Hieu. In-process measurement of topography change of grinding wheel by using hydrodynamic pressure[J], International Journal of Machine Tools & Manufacture 42(2002) 1447～1453
58. S. Ebbrell, N. H. Woolley, Y. D. Tridimas. The effects of cutting fluid application methods on the grinding process[J], International Journal of Machine Tools & Manufacture 40(2000) 209～223
59. Sun-Kyu Lee, Yuji Miyamoto, Tsunemoto. E. ects of minimizing hydrodynamic pressure in ultra-precision mirror grinding[J], International Journal of Machine Tools & Manufacture 44(2004) 1031～1036
60. Mitjan Kalin, Said Jahanmir. Influence of roughness on wear transition in glass-infiltrated alumina[J], Wear 255(2003) 669～676
61．李长河，原所先，修世超，等．超高速磨削中的砂轮自动平衡技术[J]．新技术新工艺，2004，5：29～31
62. Jeong-Du Kim. Motion analysis of powder particles in EEM using cylindrical polyurethane wheel[J], International Journal of Machine Tools & Manufacture 42(2002) 21～28
63. Shun-bin Wang and Hong-Sen Kou. Cooling effectiveness of cutting fluid in creep feed grinding[J], Heat Transfer, Vol24 No. 6 pp. 771～783, 1997
64. K. Ramesh, S. H. Yeo, Z. W. Zhong. Coolant shoe development for high efficiency grinding[J], Journal Materials Processing Technology[J], 2004, 114(4): 240～245
65. Yaw-Terng Su), Yui-Chen Kao. An experimental study on machining rate distribution of hydrodynamic polishing process[J], Wear, 1999., 224(1): 95～105
66. Ravi Saxena, Dipto G. Thakurta, Ronald J. Gutmann. A feature scale model??for chemical mechanical planarization of damascene structures[J], Thin Solid Films 449(2004) 192～206
67. Sang-Shin Park, ChuI-Ho Cho, Yoomin Ahn. Hydrodynamic analysis of chemical mechanical polishing process[J], Tribology International 33(2000) 723～730
68. Yaw-Terng Su, Tu-Chieh Hung, Chuen-Chyi Horng. An experimental study on tool wear of hydrodynamic polishing process[J], Wear 246(2000) 117～129
69. Yaw-Terng Su, Tu-Chieh Hung, Chun-Cheng Weng. Ultra-precision machining by the cylindrical polishing process[J], International Journal of Machine Tools & Manufacture 43(2003) 1197～1207
70．李长河，蔡光起．游离磨粒精密光整加工方法的机理及关键技术[J]．机床制造产业，2005，6：7～18
71．李长河，修世超，蔡光起．微细游离磨粒借助流体动压力实现的超精密加工技术[J]．机械设计与制造，2005，12：72～75
72. Jongwon Seok, Cyriaque P. Sukam, Andrew T. Kim. Multiscale material removal modeling of chemical mechanical polishing[J], Wear 254(2003) 307～320
73. Sum Huan Ng. Pad Soaking Effect on Interfacial Fluid Pressure Measurements During CMP[J], Journal of Tribology, JULY 2003, Vol. 125: 582～586
74. Lei Shan, Joseph Levert. Interfacial Fluid Mechanics and Pressure Prediction in Chemical Mechanical Polishing[J], Journal of Tribology, JULY 2000, Vol. 122: 539～543
75. Chul-Ho Cho, Sang-Shin Park, Yoomin Ahn. Three-dimensional wafer scale hydrodynamic modeling for chemical mechanical polishing[J], Thin Solid Films 389, 2001. 254～260
76. W. Che, A. Chandra. Mechanistic Understanding of Material Detachment During Micro-Scale Polishing[J], Journal of Manufacturing Science and Engineering, NOVEMBER 2003, Vol. 125: 731～735
77. Rajendra K. Jain, Vijay K. Jain, P. M. Dixit. Modeling of material removal and surface roughness in abrasive flow machining process[J], International Journal of Machine Tools & Manufacture 39(1999) 1903～192378. L. B. Zhou, H. Eda, J. Shimizu. State-of-art technologies and kinematical analysis for one-stop finishing of φ300mm Si wafer[J], Journal of Materials Processing Technology, 2002, 129(1): 34～40
79. A. Tazibt, F. Parsy, N. Abriak. Theoretical analysis of the particle acceleration process in abrasive jet cutting[J], Computational Materials Science, 1996, 5: 243～354
80. Robert W. Lyczkowsk, Jacques X. Bouillard. State-of-the-art review of erosion modeling in fluid/solids systems[J], Progress in Energy and Combustion Science 28(2002) 543～602
81. P. H. Shipway. A mechanical model for particle motion in the micro-scale abrasion wear test[J], Wear 257(2004) 984～991
82. M. Talia, H. Lankarani, J. E. Talia. New experimental technique for the study and analysis of solid particle erosion mechanisms[J], Wear, 1999, 225(12): 1070～1077
83. Jae-Mo Lee, Won-Hyuk Jin, Dae-Eun Kim. Application of single asperity abrasion process for surface micro-machining[J], Wear 251(2001) 11331143
84. Rajendra K. Jain, V. K. Jain. Specific energy and temperature determination in abrasive flow machining process[J], International Journal of Machine Tools & Manufacture 41(2001) 1689～1704
85. Wook-Bae Kim, Byung-Kwon Min. Surface Finishing and Evaluation of Three-Dimensional Silicon Microchannel Using Magnetorheological Fluid[J], Journal of Manufacturing Science and Engineering, NOVEMBER 2004, Vol. 126: 772～778
86. William L. Cooper, Adrienne S. Lavine. Grinding Process Size Effect and Kinematics Numerical Analysis[J], Journal of Manufacturing Science and Engineering, FEBRUARY 2000, Vol. 122: 59～69
87. M. S. Bingley, S. Schnee. A study of the mechanisms of abrasive wear for ductile metals under wet and dry three-body conditions[J], Wear 258(2005) 50～61
88．李长河，修世超，李琦，等．磨料喷射光整加工机理及在机械领域中的应用[J]．机械制造，2004，8：18～21
89．李长河，原所先，李虎，等．磨削区内气流场速度和压力分布规律的研究进??展[J]．金刚石与磨料磨具工程，2004，3：31～34
90. C. H. Li, G. Q. Cai, S. C. Xiu. High efficiency abrasive machining process and its key technologies[J], The 11th international conference on industrial engineering and engineering management. 2005, 4: 516～519
91. W. Che, A-F. Bastawros. Mechanistic Understanding of Material Detachment During Micro-Scale Polishing[J], Journal of Manufacturing Science and Engineering, NOVEMBER 2003, Vol. 125: 731～735
92. Wook-Bae Kim, Sung-Jun Park, Byung-Kwon Min. Surface finishing technique for small parts using dielectrophoretic effects of abrasive particles[J], Journal of Materials Processing Technology 147(2004) 377～384
93. W. J. Zong, D. Li, K. Cheng, T. Sun. The material removal mechanism in mechanical lapping of diamond cutting tools[J], International Journal of Machine Tools & Manufacture 45(2005) 783～788
94. J. Kang, M. Hadfield. Examination of the material removal mechanisms during the lapping process of advanced ceramic rolling elements[J], Wear 258(2005) 2～12
95. S. W. Lee, Y. C. Lee, H. D. Jeong. The effect of high pressure air jet on form accuracy in slot grinding[J], Journal of Materials Processing Technology 128(2002) 67～72
96. B. Lauwers, J. P. Kruth, W. Liu, W. Investigation of material removal mechanisms in EDM of composite ceramic materials[J], Journal of Materials Processing Technology 149(2004) 347～352
97. Q. H. Zhang, J. H. Zhang, Z. X. Jia. Material-removal-rate analysis in the ultrasonic machining of engineering ceramics[J], Journal of Materials Processing Technology 88(1999) 180～184
98. P. S. Sreejith, B. K. A. Ngoi. Material removal mechanisms in precision machining of new materials[J], International Journal of Machine Tools & Manufacture 41(2001) 1831～1843
99．李长河 蔡光起 李琦．砂轮约束磨粒喷射精密光整加工表面形貌创成机理研究[J]．东北大学学报(自然科学版)，2005，23(6)：581—585
100. Williams, J. A., and Hyncica, A. M.,. Mechanisms of Abrasive Wear in Lubricated Contacts. Wear[J], 1992, 152, pp. 57～74.101．赵恒华，蔡光起，超高速磨削冲击成屑的建模和机理研究[J]，中国机械工程，v 15，n 12，Jun 25，2004，p 1038～1041
102. Ronen, A., and Malkin, S.. Wear Mechanisms of Statically Loaded Hydrodynamic Bearings by Contaminant Abrasive Particles[J], Wear,, 1981, 68, pp. 371～389.
103. Buijs, M., and Korpel-van Houten, K.. Three-Body Abrasion of Brittle Materials as Studied by Lapping[J]. Wear, 1993, 166, pp. 237～245.
104．赵恒华，蔡光起，李长河，等．高效深磨中磨削温度和表面烧伤研究[J]，中国机械工程，V 15，n 22，2004，p 2048～2052
105. Y. P. Chang, M. Hanshimura and D. A. Dornfeld. An Investigation of Material Removal Mechanisms in Lapping With Grain Size Transition[J]. Journal of Manufacturing Science and Engineering, 2000, Vol. 122, 413～419.
106. K. Bose, R. J. K. Wood. Influence of load and speed on rolling micro-abrasion of CVD diamond and other hard coatings[J], Diamond and Related Materials 12(2003) 753～756
107. K. BARCOVA, M. MASHLAN and P. MARTINEC. Mossbauer Study of the Thermal Behaviour of Garnets Used in High-Energy Water Jet Technologies[J], Hyperfine Interactions 139/140: 463～469, 2002.
108. M. A. Verpui, G. de With, P. G. Th. Bed thickness and particle size distribution in three body abrasion[J], Wear 188(1995) 102～107
109. P. H. Shipway. The role of test conditions on the microabrasive wear behaviour of soda-lime glass[J], Wear 233-235 1999 191～199
110. Yuan-Zhong Hu, Dong Zhu. A Full Numerical Solution to the Mixed Lubrication in Point Contacts, Journal of Tribology[J], JANUARY 2000, Vol. 122: 1～9
111. P. I. YASCHERITSIN AND L. E. SERGEEV, The Comparative Appraisal of Quality Characteristics of Holes after Different Finishing Methods[J], Advanced Performance Materials 4, 337～347(1997)
112. M. A. Verspui, G. de With, A. Corbijn. Simulation model for the erosion of brittle materials[J], Wear 233-235 1999 436～443
113 修世超，李长河，蔡光起．磨削加工表面粗糙度理论模型修正方法[J]，东北大学学报(自然科学版)，2005，26(8)：770—774
114 臼井英治．切削磨削加工学[M]．高希正，译．北京：机械工业出版社，1982，482??—492.
115. Yaw-Terng Su, Chuen-Chyi Horng,Yeong-Dong Hwang. Effects of tool surface irregularities on machining rate of a hydrodynamic polishing process[J], Wear, 1996, 199(1): 89～99
116. T. R. Loveless, R. E. Williams, K. P. Rajurkar. A study of the effects of abrasive-flow finishing on various machined surfaces[J], Journal of Materials Processing Technology, 1994, 47(1): 133～151
117. Rajendra K. Jain, Vijay K. Jain*, P. M. Dixit. Modeling of material removal and surface roughness in abrasive flow machining process[J], International Journal of Machine Tools & Manufacture, 1999, 39(12): 1903～1923
118. Rajendr K. Jain, V. K. Jain. Stochastic simulation of active grain density in abrasive flow machining[J], Journal of Materials Processing Technology, 2004, 152(1): 17～22
119. V. K. Jain *, S. G. Adsul. Experimental investigations into abrasive flow machining(AFM)[J], International Journal of Machine Tools & Manufacture2000, 40(10): 1003～1021
120. Jeong-Du Kim, Min-Seog Choi. Simulation for the prediction of surface-accuracy in magnetic abrasive machining[J], Journal of Materials Processing Technology, 1995, 53(6): 630～642
121. Sunil Jha, V. K. Jain_ Design and development of the magnetorheological abrasive flow finishing(MRAFF) process[J], International Journal of Machine Tools & Manufacture, 2004, 44(10): 1019～1029
122. Hee-Won Jeong, Tetsuya Aoki, Takeshi Hatsuzawa. High-efficiency fixed abrasive polishing method for quartz crystal blanks[J], International Journal of Machine Tools & Manufacture 44(2004) 167～173
123. Ravi Saxena, Dipto G. Thakurta, Ronald J. Gutmann. A feature scale model for chemical mechanical planarization of damascene structures[J], Thin Solid Films 449(2004) 192～206
124. Jongwon Seok, Cyriaque P. Sukam, Andrew T. Kim. Material removal model for chemical-mechanical polishing considering wafer flexibility and edge effects[J], Wear 257(2004) 496～508
125．李长河，蔡光起，李琦，等．砂轮约束磨粒喷射精密光整加工材料去除机理研究[J]．中国机械工程，2005，16(23)：2116～2120126. Chul-Ho Cho, Sang-Shin Park, Yoomin Ahn. Three-dimensional wafer scale hydrodynamic modeling for chemical mechanical polishing[J], Thin Solid Films 389Z2001. 254～260
127. T. Mori, K. Hirota, Y. Kawashima. Clarification of magnetic abrasive finishing mechanism[J], Journal of Materials Processing Technology 143-144(2003) 682～686
128. N. Umehara, R. Komanduri. Magnetic fluid grinding of HIP-Si_3N_4 rollers[J], Wear, 1996, 192(1): 85～93
129. Dhirendr K. Singhl, V. K. Jain, V. Raghuram. Parametric study of magnetic abrasive finishing process[J], Journal of Materials Processing Technology 149(2004) 22～29
130. I. Zarudi, L. C. Zhang. On the Limit of Surface Integrity of Alumina by Ductile-Mode Grinding[J], Journal of Engineering Materials and Technology, 2000, 122(3): 129～134
131. S. Wan, G. C. Lim. Transient Flow in Abrasive Suspension Jet Cutting Machines on Pump Shutdown[J], Journal of Manufacturing Science and Engineering, 2003, 125(2): 172～178
132．李长河，孙奕澎，蔡光起．自由磨粒复杂曲面磁力研磨光整加工试验研究[J]．制造技术与机床，2005，5：72～75
133. [1] Y. P. Chang, M. Hanshimura and D.A.Dornfeld. An Investigation of Material Removal Mechanisms in Lapping With Grain Size Transition[J]. Journal of Manufacturing Science and Engineering, 2000, Vol. 122, 413～419.
134. Buijs, M., and Korpel-van Houten, K.. Three-Body Abrasion of Brittle Materials as Studied by Lapping[J]. Wear, 1993, 166, pp. 237～245.
135. R. Chauhan, Y. Ahn, S. Chandrasekar, et al. Role of Indentation fracture in free abrasive machining of ceramics. Wear, 162-164(1993) 246～257.
136. M. Buils, K. Korpel and Van Houten. A model for lapping of glass[J], Journal of Materials Science 28(1993) 3014～3020.
137. L. Fang, L. Kong, J. Y. Su. Movement patterns of abrasive particles in three body abrasion[J], Wear, 162-164(1993) 782～789.
138. Sunil Jha, V. K. Jain. Design and development of the magnetorheological abrasive flow finishing(MRAFF) process[J], International Journal of Machine??Tools & Manufacture, 2004, 44(10): 1019～1029
139. Rajendra K. Jain, V. K. Jain. Stochastic simulation of active grain density in abrasive flow machining[J], Journal of Materials Processing Technology, 2004, 152(1): 17～22
140. Rajendra K. Jain, V. K. Jain. Specific energy and temperature determination in abrasive flow machining process[J], International Journal of Machine Tools & Manufacture, 2001, 41(12) 1689～1704
141. V. K. Jain, S. G. Adsul. Experimental investigations into abrasive flow machining(AFM)[J], International Journal of Machine Tools & Manufacture, 2000, 40(9): 1003～1021
142. Baogui Shi, J. L. Sullivan, M. A. Wild. Study of Generation Mechanism of Three-Body Particles in LinearTape Recording[J], Journal of Tribology, 2005, 127(2): 155～163
143. M. A. Verspui, G. De With, P. G. Th. Bed thickness and particle size distribution in three-body abrasion[J], Wear, 1995, 188(2): 102～107
144. R. I. Trezona, D. N. Allsopp, I. M. Hutchings. Transitions between two-body and three-body abrasive wear: influence of test conditions in the microscale abrasive wear test[J], Wear, 1999, 225(6):. 205～214
145. J. D. Gates. Two-body and three-body abrasion: A critical discussion[J], Wear, 1998, 214(2): 139～146
146．李长河，蔡光起，原所先．砂轮约束磨粒喷射精密光整加工材料去除模型[J]．农业机械学报，2005，36(11)：132～135
147. M. Bhagavat, V. Prasad, I. Kao. Elasto-Hydrodynamic Interaction in the Free Abrasive Wafer Slicing Using a Wiresaw: Modeling and Finite Element Analysis[J], Journal of Tribology, 2000, 122(4): 394～404
148. P. H. Shipway. The role of test conditions on the microabrasive wear behaviour of soda-lime glass[J], Wear, 1999, 233(3): 191～199
149. Yeong Yan Guu. Correlation between three-body wear and tribological characteristics of titanium nitride, titanium carbonitride and titanium carbide coatings[J], Wear, 1997, 208(3): 147～154
150. K. Bose, R. J. K. Wood. Influence of load and speed on rolling micro-abrasion of CVD diamond and other hard coatings[J], Diamond and Related Materials, 2003, 12(9): 753～756151.O.P. Modi_, B.K. Prasad, A.K. Jha, Low-stress abrasive wear behaviour of a 0.2% C steel: influence of microstructure and test parameters[J], Tribology Letters, 2003,15(3):249—255
152.Y. Ueharaa, M. Wakudab, Y. Yamauchic, Tribological properties of dimpled silicon nitride under oil lubrication[J], Journal of the European Ceramic Society,2004,24 (5) :369—373
153.Ming Chen, Koji Kato, Koshi Adachi. Friction and wear of self-mated SiC and Si3N4 sliding in water[J], Wear,2001, 250 (5): 246-255
154.Kah Fai Leong, Chee Kai Chua, Gim Siong Chua. Abrasive jet deburring of jewellery models built by stereolithography apparatus (SLA)[J], Journal of Materials Processing Technology ,1998,83 (1): 36—47
155.Mohammad Reza Baghbanan, Akihiro Yabuki, Roland S. Tribological behavior of aluminum alloys in a vibratory finishing process[J], Wear ,2003,255 (10): 1369-1379
156.Mitjan Kalin, Said Jahanmir. Influence of roughness on wear transition in glass-infiltrated alumina[J], Wear ,2003,255(7):669~676
157.U. Dulias, L. Fangb, K.-H. Zum Gahr. Effect of surface roughness of self-mated alumina on friction and wear in isooctane-lubricated reciprocating sliding contact[J], Wear, 2002,252 (7) :351~358
158.H.H. Tsai, H. Hocheng. Prediction of a thermally induced concave ground surface of the workpiece in surface grinding[J], Journal of Materials Processing Technology, 2002,122 (4): 148—159
159.Y.P.Chang, M.Hanshimura and D.A.Dornfeld. An Investigation of Material Removal Mechanisms in Lapping With Grain Size Transition[J]. Journal of Manufacturing Science and Engineering, 2000, Vol.122, 413—419.
160.Buijs, M., and Korpel-van Houten, K.Three-Body Abrasion of Brittle Materials as Studied by Lapping[J]. Wear, 1993, 166, pp. 237—245.
161.R. Chauhan, Y. Ahn, S.Chandrasekar.et al. Role of Indentation fracture in free abrasive machining of ceramics[J]. Wear, 162-164 (1993) 246—257.
162.Yutaka Hasegawa.Sasuke Miyazima. Polishing rate for (100) and (110) surfaces[J], Physical A, 1996,233(8):663—671
163.Ming Jiang, Nelson O. On chemo-mechanical polishing(CMP) of silicon nitride (Si_3N_4) workmaterial with various abrasives [J], Wear, 1998,220(1): 59～71
164. C. H. Li, G. Q. Cai, S. C. Xiu. Material Removal Model and Experimental Verification for Abrasive Jet Precision Finishing with Wheel as Restraint[J], Key Engineering Materials, 2006. Vol. 304-305: 555～559
165. Yaw-Terng Su, Yui-Chen Kao. An experimental study on machining rate distribution of hydrodynamic polishing process[J], Wear, 1999, 224(3): 95～105
166. Jongwon Seok, Cyriaque P. Sukam, Andrew T. Kim. Material removal model for chemical-mechanical polishing considering wafer flexibility and edge effects[J], Wear, 2004, 257(8): 496～508
167．李伯奎，刘远伟．表面粗糙度理论发展研究[J]，2004，38(4)：63～67
168．梁嵘，李达成，曹芒．表面微观形貌测量及其参数评定的发展趋势[J]，光学技术，1998，6：66～68
169．李丽伟，董申，程凯．表面微观形貌定量表征中几种新方法的应用[J]，中国机械工程，2002，13(19)：1702～1705
170．陈艺，岳梅，焦明华．采用计算机数据处理的表面形貌分析方法及应用[J]，淮南矿业学院学报，1995，15(3)：60～63
171．李伯奎．传统机械加工表面形貌评定的缺陷及发展方向[J]，淮阴工学院学报，2002，11(3)：63～65
172．李成贵．粗糙表面轮廓相关性的倒谱分析[J]，机械工程学报，2004，40(5)：87～91
173．蒋庄德，王海容，陈伟．分数布朗运动应用于机械加工表面形貌的评定[J]，现代计量测试，1997，6：15～19
174．李长河，蔡光起，刘枫．砂轮约束磨粒喷射精密光整加工工艺特性研究[J]．金刚石与磨料磨具工程，2005，5：26～29
175．汪慰军，吴昭同，陈历喜．基于分形的表面形貌特征描述与评定参数的研究[J]，计量学报，1998，19(2)：147～151
176．王飞，罗志增．基于功率谱的表面EMG信号运动模式识别[J]，杭州电子科技大学学报，2005，25(2)：37～40
177．金鑫，张之敬．基于制造特性的微小型构件表面形貌数值模型[J]，北京理工大学学报，2005，25(3)：189～193
178．葛世荣，陈国安．磨合表面形貌变化的特征粗糙度参数表征[J]，中国矿业大学学报，1999，28(3)：204～208179．马争，桂长林．评定磨合表面的最佳形貌参数[J]，摩擦学学报，1995，1995，15(4)：133～137
180．刘晓军，肖少军，谢铁邦．曲面表面粗糙度、波度及形状误差综合测量与分析的研究[J]，1997，31(3)：33～36
181．李成贵，董申．三维表面微观形貌的表征参数和方法[J]，宇航计测技术，1999，19(6)：33～32
182．李长河，修世超，蔡光起．高速超高速磨削工艺及其实现技术[J]．金刚石与磨料磨具工程，2004，4：16～20
183．李成贵，马小丽，袁长良．三维加工表面形貌等方性评定的研究[J]，太原工业大学学报，1996，27(1)：13～19
184．张滢，王维．虚拟数控车削表面形貌的仿真与表面粗糙度预测[J]，现代制造工程，2005，7：24～26
185．于思远，林彬，林滨．工程陶瓷超精密磨削表面质量的研究[J]，金刚石与磨料磨具工程，2002，5：12～19
186．周锦进，翟小兵，庞桂兵．脉冲电化学光整加工表面微观形貌的研究[J]，农业机械学报，2004，35(3)：150～153
187．蒋书文，姜斌，李燕．磨损表面形貌的三维分形维数计算[J]，摩擦学学报，2003，23(6)：433～436
188．王安良，杨春信．评价机械加工表面形貌的小波变换方法[J]，机械工程学报，2001，37(8)：65～70
189．梁洁，李尚平．用STM对高速磨削表面微观形貌的研究[J]，金刚石与磨料磨具工程，2001，3：7～10
190. D. Arola, M. Ramulu. Material removal in abrasive waterjet machining of metals surface integrity and texture[J], Wear, 1997, 210(6): 50～58
191. S. Paul, A. M. Hoogstrate, C. A. van Luttervelt. Analytical and experimental modelling of the abrasive water jet cutting of ductile materials[J], Journal of Materials Processing Technology, 1998, 73(3): 189～199
192. F. L. Chen, J. Wang, E. Lemma. Striation formation mechanisms on the jet cutting surface[J], Journal of Materials Processing Technology, 2003, 141(4): 213～218
193. Y. Uehara, M. Wakuda, Y. Yamauchi. Tribological properties of dimpled silicon nitride under oil lubrication[J], Journal of the European Ceramic Society, 2004, 24(5): 369～373194. M. Kantha Babu, O. V. Krishnaiah Chetty. A study on recycling of abrasives in abrasive water jet machining[J], Wear, 2003, 254(9): 763～773
195．周熙熙，阎秋生．磨料喷射加工加工特性研究[J]，机械研究与应用，2003，16(3)：30～32
196. Keyurkumar, J. Patel. Quantitative evaluation of abrasive contamination in ductile material during abrasive water jet machining and minimizing with a nozzle head oscillation technique[J], International Journal of Machine Tools & Manufacture, 2004, 44(6): 1125～1132
197. R. Balasubbramaniam, J. Krishnan, N. Ramakrishnan. Astudy on the shape of the surface generated by abrasive jet machining[J], Journal of Materials Processing Technology, 2002, 121(1): 102～106
198. A. Jourani, M. Dursapt, H. Hamdi. Effect of the belt grinding on the surface texture: Modeling of the contact and abrasive wear[J], Wear, 2005, 259(11): 1137～1143
199. Jeong-Du Kim, Min-Seong Choi. Simulation for the prediction of surface-accuracy in magnetic abrasive machining[J], Journal of Materials Processing Technology, 1995, 53(6): 630～642
200. T. K. Puthanangady, S. Malkin. Experimental investigation of the superfinishing process[J], Wear, 1995, 185(2): 173～182
201．李长河，蔡光起，修世超．低温冷却磨削机理研究[J]．金刚石与磨料磨具工程，2006，1：17～20
202．田欣利，于爱兵，林彬．陶瓷磨削残余应力对表面性能的影响[J]，机械科学与技术，2002，21(4)：615～617
203．刘菊东，王贵成，陈康敏，等．非淬硬钢磨削表面硬化层的试验研究[J]，中国机械工程，2005，16(11)：1013～1017
204．杨斌久，盖全芳，张玉峰．高速磨削加工的残余硬度[J]，长春工业大学学报(自然科学版)，2004，25(1)：41～43
205．冯宝富，马春容．淬硬轴承钢磨削后的表面硬度[J]，辽宁石油化工大学学报，2005，25(2)：41～44
206．王宗英，肖楠，吕淑萍．40Cr钢表面改性处理及磨损性能研究[J]，沈阳建筑大学学报(自然科学版)，2005，21(3)：281～284
207．李长河，赵亮，蔡光起．利用磨削热进行表面热处理的新工艺技术研究[J]．2005，1：61—64208．刘菊东，王贵成，陈康敏．65Mn钢磨削硬化层组织的研究[J]，中国机械工程，2004，15(17)：1073～1076
209．邓守军，孙乐民，李占君．PCrMo钢的摩擦磨损特性实验研究[J]，润滑与密封，2005，4：84～85
210．孙月海，张新，郑惠江．蜗杆传动用摩擦副材料在滑动干摩擦条件下的摩擦磨损性能研究[J]，摩擦学报，2005，25(3)：279～282
211．常海波，徐洮，李红轩．用等离子体增强化学气相沉积技术制备类金刚石碳薄膜的摩擦磨损性能研究[J]，摩擦学学报，2005，25(4)：298～302
212．杨卓娟，韩志武，任露泉．激光处理凹坑形仿生非光滑表面试件的高温摩擦磨损特性研究[J]，摩擦学学报，2005，25(4)：374～378
213．张永振，邱明，上官宝．高速干摩擦条件下铝基复合材料的摩擦磨损行为研究[J]，摩擦学学报，2005，25(4)：343～347
214．李长河，蔡光起．超高速磨削技术的特点及在工业中的具体应用[J]．通用机械，2005，7：69～72
215．王振廷，陈华辉．碳化钨颗粒增强金属基复合材料涂层组织及其摩擦磨损性能[J]，摩擦学学报，2005，25(3)：204～207
216．徐桂芳，程晓农，司乃潮．不同磨损介质下铜锌铝形状记忆合金滚动磨损性能与磨损机制研究[J]，新技术新工艺，2004，8：46～49
217．邢建东，高义民，张国赏．不锈钢与高碳钢的冲刷腐蚀磨损试验研究[J]，西安交通大学学报，2004，38(5)：469～473
218．丁厚福，崔方明，杜晓东．成分和组织对衬板钢在腐蚀料浆环境下的冲击磨损性能与机理的影响[J]，摩擦学学报，摩擦学学报，2005，25(4)：222～225
219．郭亮，丁厚福，严小冲．低碳高合金钢和高锰钢冲击腐蚀磨损特性研究[J]，兵器材料科学与工程，2005，28(2)：12～16
220．丁厚福，崔方明，杜晓东．腐蚀条件下冲击功对钢冲击磨损性能与机制的影响[J]，材料热处理学报，2004，26(2)：55～61
221．李先芬，苏勇，陈翌庆．两种钢冲击腐蚀磨损性能的试验研究[J]，兵器材料科学与工程，2003，26(3)：18～21
222．王安东，戴起勋．生物医用材料316L不锈钢的磨损腐蚀特性研究[J]，金属热处理，2005，30(3)：33～36
223．张慧君．自相关函数在机械故障分析中应用[J]，机械工艺师，2001，8：19～20
224．陈历喜．用随机分析的方法研究电加工表面形貌[J]，航空工艺技术，1995，2：??15～19
225．李西琴，陈历喜，汪慰军．用互相关函数判别零件表面形貌的特征[J]，机械科学与技术，1998，17(1)：49～51
226．邢彦锋，张明，侯仰海．电化学机械光整加工表面相关性分析[J]，山东理工大学学报：自然科学版，2003，17(3)：23～26
227．车建明．炭纤维增强铜基复合材料摩擦磨损性能同其磨损表面形貌相关性研究[J]，摩擦学学报，摩擦学学报，2004，24(2)：144～147
228．李惠芬，蒋向前，李柱．三维表面形貌的功能评定方法[J]，宇航计测技术，2001，21(6)：19～26
229．郝达兵，姜岩峰，黄庆安．各向异性腐蚀表面粗糙度的“应力模型”[J]，光电子技术，2003，23(3)：202～206
230．沈卫星，徐德衍．强激光光学元件表面功率谱密度函数估计[J]，强激光与粒子束，2000，12(4)：392～396
231．苑伟政，马炳和，李小莹．硅的准分子激光直写刻蚀微细加工特性研究[J]，机械工程学报，2000，36(3)：107～110
232. T. A. STOLARSKI. Attrition of silicon nitride as a function of counterface material and contact zone kinematics[J], JOURNAL OF MATERIALS SCIENCE 36(2001) 1911～1919
233. H. JOHANSEN, G. KASTNER. Surface quality and laser-damage behaviour of chemo-mechanically polished CaF2 single crystals characterized by scanning electron microscopy[J], JOURNAL OF MATERIALS SCIENCE 33(1998) 3839～384
© 2004-2018 中国地质图书馆版权所有 京ICP备05064691号 京公网安备11010802017129号 地址：北京市海淀区学院路29号 邮编：100083 电话：办公室：(+86 10)66554848；文献借阅、咨询服务、科技查新：66554700 |