磁脉冲焊接外管周向变形研究

详细信息    查看全文 | 推荐本文 |

英文篇名：Study on Circumferential Deformation of Outer Tube during Magnetic Pulse Welding 作者：陈树君 ; 阚纯磊 ; 袁涛 ; 蒋晓青 英文作者：CHEN Shujun;KAN Chunlei;YUAN Tao;JIANG Xiaoqing;College of Mechanical Engineering and Applied Electronics Technology, Beijing University of Technology; 关键词：Ansoft ; Maxwell电磁仿真软件 ; 集磁器开口间隙 ; 电磁脉冲焊接 英文关键词：Ansoft Maxwell electromagnetic simulation software;;opening gap of field shaper;;magnetic pulse welding 中文刊名：SJGY 英文刊名：Hot Working Technology 机构：北京工业大学机械工程与应用电子技术学院; 出版日期：2019-05-14 15:25 出版单位：热加工工艺 年：2019 期：v.48;No.511 基金：国家自然科学基金面上项目(51575012) 语种：中文; 页：SJGY201909057 页数：4 CN：09 ISSN：61-1133/TG 分类号：203-205+211

摘要

采用Ansoft Maxwell电磁仿真软件模拟了磁脉冲焊接中外管表面磁感应强度分布,研究了外管周向磁感应强度分布。通过空管变形实验研究了放电电压对外管变形的影响,并以此来验证仿真结果。结果表明:集磁器开口间隙减弱了其附近位置外管上的磁感应强度,并且随着电压的增大,这种不均匀性加剧。空管变形实验表明,外管在集磁器开口间隙附近变形量比周向其它位置小,随着电压的增大,这种变形差异逐渐增大。
        The surface magnetic induction intensity distribution of the outer tube in magnetic pulse welding was stimulated by using Ansoft Maxwell electromagnetic simulation software, and the circumferential magnetic induction intensity distribution of outer tube was investigated. The deformation of outer tube was researched by blank tube deformation experiments, and the simulation results were verified by this method. The results show that the opening gap of field shaper weakens the magnetic induction of the outer tube near the field shaper opening gap, and non-uniformity of magnetic induction intensity increases with the increase of the voltage. The blank tube deformation experiment shows that the deformation of the outer tube near the opening gap of field shaper is smaller than that of the other positions in the circumferential direction. With the increase of the voltage, the difference of the deformation increases gradually.

引文

[1]陈树君,夏羽,于洋,等.磁脉冲焊接机理及其在异种金属材料连接中的应用[J].焊接,2010(12):9-14.
    [2]李春峰,张景辉,赵志衡,等.胀形用集磁器的实验研究[J].哈尔滨工业大学学报,2000(4):107-109.
    [3]Niayesh K,Karimi A,Bahmani M A.3D Simulation of magnetic field distribution in electromagnetic forming systems with field-shaper[J].Journal of Materials Processing Technology,2009,209(5):2295-2301.
    [4]Garzan E,Ebrahimi H,Fallahi Arezoodar A.Effect of various field shapers on magnetic pressure in electromagnetic inward tube forming[J].Journal of Iron and Steel Research(International),2012(s1):86-89.
    [5]Wang H,Liu W,Gai W,et al.Modeling and prototyping of a flux concentrator for positron capture[J].IEEE Transactions on Magnetics,2008,44(10):2402-2408.
    [6]范治松.20#钢/3A21铝管磁脉冲复合工艺研究[D].哈尔滨:哈尔滨工业大学,2012.