某车用变速器输出轴齿轮断齿失效原因分析

详细信息    查看全文 | 推荐本文 |

	英文篇名：Analysis of Transmission Output Shaft Teeth Broken 作者：陈慧 英文作者：CHEN Hui;Pan Asia Technical Automotive Center Co.,Ltd.; 关键词：输出轴 ; 断齿 ; 失效分析 英文关键词：output shaft;;teeth broken;;failure analysis 中文刊名：CYGS 英文刊名：Design and Manufacture of Diesel Engine 机构：泛亚汽车技术中心有限公司; 出版日期：2019-06-25 出版单位：柴油机设计与制造 年：2019 期：v.25;No.167 语种：中文; 页：CYGS201902007 页数：6 CN：02 ISSN：31-1430/TH 分类号：31-36

摘要

针对某车用变速器输出轴发生断齿故障,借助扫描电镜、金相分析、硬度检测、X射线衍射等各种理化手段对失效原因进行了深入分析与研究。结果表明输出轴齿轮发生断齿是因齿轮心部硬度不够,影响齿轮的接触疲劳强度和弯曲疲劳强度,导致齿轮的齿在高应力作用下疲劳开裂。根据失效分析的结果,提出优化改进措施,最终确保零件顺利通过严苛的台架耐久试验。
        The transmission output shaft of a vehicle had the problem of teeth broken. To address the problem,a thorough analysis and research on the failure cause was made by means of scanning electron microscope,metallographic examination,hardness tests,X-Ray,etc. The results showed that the failure was due to low strength in gear center,which effected the contacting and bearing fatigues,resulting in teeth crack under high stress. Several optimization measures based on the analysis results were proposed and implemented. As a result,the improved shaft passed the dyno durability tests successfully.

引文

[1] XUAN H J,SONG J. Failure analysis and optimization design of a centrifuge rotor[J]. Engineering Failure Analysis,2007,14(1):101-109.
    [2]孙维连,陈再良,王成彪.机械产品失效分析思路及失效案例分析[J].材料热处理学报,2004:69-73.
    [3]张栋,钟赔道,陶春虎,等.失效分析[M].北京:国防工业出版社,2008.
    [4]任颂赞,叶俭,陈德华.金相分析原理及技术[M].上海:上海科学技术文献出版社,2012.
    [5]潘艳春,董笑飞,陈然.齿轮钢带状组织微区成分偏析表征方法探讨[J].汽车工艺与材料,2017(5):45-47.
    [6]张迎晖,赖泓州,赵鸿金.钢中带状组织的研究现状[J].轧钢,2014,31(3):45-46.
    [7] AHMED M,SALAM I,HASHMI F H. Influence of banded structure on the mechanical properties of a high-strength maraging steel[J]. Journal of Materials Engineer and Performance,1997,6(2):165-171.
    [8]王民方.锻件带状组织的分析与热处理[J].锻压机械,2002(1):39-40.
    [9]黄丽荣,汤宏智.汽车齿轮硬化层深度设计[J].热处理技术与装备,2008,29(6):28-32.
    [10]成丽.喷丸齿轮残余应力数值分析与仿真[J].机械研究与应用,2016(5):22-26.
    [11]胡一丹,郑文,徐红辉,等.渗碳齿轮钢残余内应力的研究[J].河南科技大学学报,2007,28(4):1-4.
    [12]陈德华,滕鲁湘,李光谨,等.渗碳淬硬层残余应力的分布特征[J].热处理,2011,26(2):65-71.