第二法向应力差与气辅共挤出胀大的关系

详细信息    查看全文 | 推荐本文 |

英文篇名：Relation Between Secondary Normal Stress Difference and Die Swell in Gas-Assisted Coextrusion Process 作者：邓小珍 ; 曾宇露 ; 肖兵 ; 唐刚 ; 张志杰 英文作者：DENG Xiaozhen;ZENG Yulu;XIAO Bing;TANG Gang;Zhang Zhijie;Jiangxi Province Key Laboratory of Precision Drive & Control,Nanchang Institute of Technology;Jiangxi Province Key Laboratory of Polymer Preparation and Processing,Shangrao Normal University; 关键词：第二法向应力差 ; 气辅共挤 ; 挤出胀大 ; 黏弹流动 ; 数值模拟 英文关键词：secondary normal stress difference;;gas-assisted coextrusion;;die swell;;viscoelastic flow;;numerical simulation 中文刊名：XJKB 英文刊名：Materials China 机构：南昌工程学院江西省精密驱动与控制重点实验室;上饶师范学院江西省塑料制备成型重点实验室; 出版日期：2019-05-15 出版单位：中国材料进展 年：2019 期：v.38;No.449 基金：江西省教育厅科研技术研究项目(GJJ161124,GJJ161103);; 江西省塑料制备成型重点实验室开放基金项目(JXSR201603);; 江西省重点研发计划项目(20151BBE50044) 语种：中文; 页：XJKB201905014 页数：6 CN：05 ISSN：61-1473/TG 分类号：109-114

摘要

采用Phan-Thien-Tanner(PTT)本构方程描述聚合物熔体共挤分层流动的黏弹行为,建立了C形双层气辅共挤非等温流动理论模型,并数值实现,研究了熔体入口体积流率对挤出胀大率和第二法向应力差的影响,同时分析了熔体挤出胀大率与第二法向应力差之间的规律性联系。研究结果表明,当两熔体流率不相等时,单层熔体挤出胀大率随着自身流率的增大而增大,随着另一熔体流率的增大而减小,甚至出现负值;当两熔体流率相等时,单层熔体挤出胀大率不随流率的变化而变化;熔体整体挤出胀大率则不随流率的变化而变化,始终接近零值;熔体的挤出胀大率与第二法向应力差有关,且正比于第二法向应力差的绝对值。
        A 3D non-isothermal viscoelastic numerical model was found for a two-layer gas-assisted coextrusion through the C-profiled channel with PTT model describing the viscoelastic flow behavior of molten polymer and the simulation was carried out. The influence of melt inlet volumetric flow rate on die swell and secondary normal stress difference was researched and the relation between dying swell and secondary normal stress difference was investigated. The study results show that the melt swell ratio increases with its flow rate increasing and decreases with other melt flow rate increasing when two melts' flow rate is not equal. The melt flow rate has little influence on melt swell ratio when two melts' flow rate is equal. But the whole die swell ratio is always close to zero,whether the flow rate of the two melts is equal or not. In addition,the die swell ratio is proportional to the second normal stress difference in a gas-assisted coextrusion process.

引文

[1] Huang Yibin(黄益宾),Liu Hesheng(柳和生),Huang Xingyuan(黄兴元). Journal of Basic Science and Engineering(应用基础与工程科学学报)[J],2010,18(4):657-665.
    [2] Masanori T,Shin-ichi K,Funatsu K. Rheologica Acta[J],1998,37(6):624-634.
    [3] Zatloukal M,Kopytko W,Saha P,et al. Plastics,Rubber and Composites[J],2005,34(9):403-409.
    [4] Xu Peixian(徐佩弦). Polymer Rheology and Its Application(高聚物流变学及其应用)[M]. Beijing:Chemical Industry Press,2003.
    [5] Zhou Yanhao(周彦豪). Rheology Fundamentals of Polymer Processing(聚合物加工流变学基础)[M]. Xi'an:Xi'an Jiaotong University Press,1988.
    [6] Graessley W W,Glasscock S D,Crawley R L. Journal of Rheology[J],1970,14(4):519-526.
    [7] Garcia-Rejon A,Diraddo R W,Ryan M E. Journal of Non-Newtonian Fluid Mechanics[J],1995,60(2-3):107-128.
    [8] Liang J Z. Polymer Testing[J],2008,27(8):936-940.
    [9] Deng Xiaozhen(邓小珍),Liu Hesheng(柳和生),Huang Yibin(黄益宾). China Plastics[J],2013,27(2):74-79.
    [10] Zhang Min(张敏),Huang Chuanzhen(黄传真),Sun Sheng(孙胜),et al. Polymer Materials Science and Engineering[J],2012,28(6):176-179.
    [11] Karagiannis A,Hrymak A N,Vlachopoulos J. Rheologica Acta[J],1990,29(1):71-87.
    [12] Keawkanoksilp C,Apimonsiri W,Patcharaphun S,et al. Journal of Applied Polymer Science[J],2012,125(3):2187-2195.
    [13] Ren Zhong(任重),Huang Xingyuan(黄兴元),Liu Hesheng(柳和生). Journal of Basic Science and Engineering[J],2015,23(5):1025-1034.
    [14] Phan-Thien N,Tanner R I. Journal of Non-Newtonian Fluid Mechanics[J],1977,2(4):353-365.
    [15] Yue P T,Dooley J,Feng J J. Journal of Rheology[J],2008,52(1):315-332.