预扭转及退火热处理对TA2拉伸力学性能的影响
|
摘要
研究了预扭转和退火热处理对TA2拉伸力学性能的影响。结果表明,预扭转可显著增强TA2的拉伸屈服强度和极限强度,在一定范围内屈服强度随预扭转角增加而增大,当预扭转角超过一定值(6π)时,屈服强度急剧下降;极限强度随预扭转角增大一直呈上升趋势;延伸率随预扭转角的增加逐渐降低。预扭转后TA2不同温度(350～750℃)下的退火热处理试验表明,随着退火温度的提高,TA2强度逐渐降低,650℃时其强度已降低至母材初始值;延伸率随退火温度的升高而逐渐升高,但不能完全恢复至母材初始值。观察断口发现,随着预扭转角增加断口韧窝逐渐变小、变浅,预扭转为8π时出现了河流发散状的解理条纹。金相组织表明,预扭转后产生的大量孪晶和形变组织是导致TA2强度增大的主要原因。
The effects of pre-torsion and annealing heat treatment on the tensile mechanical properties of TA2 were studied. According to tensile test results, the pre-torsion can significantly enhance the tensile yield strength and ultimate strength of TA2. The yield strength increases with the increase of pre-torsion angle in a certain range, and drops sharply when the pre-torsion angle exceeds a certain value(6π). The ultimate strength increases all the time with the pre-torsion angle increasing. The elongation decreases with the increase of pre-torsion angle. Subsequent annealing heat treatment tests of pre-torsion TA2 at different temperatures(350～750 °C) show that the strength gradually decreases with the increase of annealing temperature. When the temperature is 650 °C, the strength has been reduced to the initial value of parent metal. The elongation increases with the increase of temperature, but it cannot recover to its initial value of parent material. The observation of fracture surface shows that dimple gets smaller and shallower with the increase of pre-torsion, and there are lots of cleavage striation characterized by river pattern when pre-torsion angle is 8π. The observation of SEM shows that twins and deformation tissues after the pre-rotation is the main reason for the increase of TA2 strength.
The effects of pre-torsion and annealing heat treatment on the tensile mechanical properties of TA2 were studied. According to tensile test results, the pre-torsion can significantly enhance the tensile yield strength and ultimate strength of TA2. The yield strength increases with the increase of pre-torsion angle in a certain range, and drops sharply when the pre-torsion angle exceeds a certain value(6π). The ultimate strength increases all the time with the pre-torsion angle increasing. The elongation decreases with the increase of pre-torsion angle. Subsequent annealing heat treatment tests of pre-torsion TA2 at different temperatures(350～750 °C) show that the strength gradually decreases with the increase of annealing temperature. When the temperature is 650 °C, the strength has been reduced to the initial value of parent metal. The elongation increases with the increase of temperature, but it cannot recover to its initial value of parent material. The observation of fracture surface shows that dimple gets smaller and shallower with the increase of pre-torsion, and there are lots of cleavage striation characterized by river pattern when pre-torsion angle is 8π. The observation of SEM shows that twins and deformation tissues after the pre-rotation is the main reason for the increase of TA2 strength.
引文
[1]Wang Guisheng(王桂生).Application Technology of Titanium(钛的应用技术)[M].Changsha:Central South University Press,2007:7
[2]Xing Jian(邢健),Ju Jianhui(巨建辉),Yang Liying(杨英丽)et al.Rare Metal Materials and Engineering(稀有金属材料与工程)[J],2013,42(8):1617
[3]Chang L,Zhou C Y,He X H.Metals-Open Access Metallurgy Journal[J],2017,7:99
[4]Wu Zhiyu(吴志煜).Thesis for Master(硕士论文)[D].Kunming:Kunming University of Science and Technology,2012
[5]Liu Ruitang(刘瑞堂),Zhou Xinping(周欣萍),Yin Jiancheng(尹建成)et al.Materials for Mechanical Engineering(机械工程材料)[J],2006,30(5):84
[6]Xia Xingyou(夏兴有).Thesis for Master(硕士论文)[D].Harbin:Harbin Engineering University,2007
[7]He Yunzeng(何蕴增),Zou Guangping(邹广平),Pan Xinji(潘信吉)et al.Journal of Experimental Mechanics(实验力学)[J],1994,9(3):262
[8]Guo N,Li X X,Xiao M et al.Advanced Engineering Materials[J],2016,18(10):1738
[9]Zhou Li(周利).Acta Mechanica Solida Sinica(固体力学学报)[J],1994,15(2):185
[10]Li Z.Acta Mechanica Solida Sinica[J],1994,107(3):229
[11]Jia Xiangya(贾祥亚),Liu Yinqi(刘茵琪),Qu Yinhua(曲银化)et al.Development and Application of Materials(材料开发与应用)[J],2013(5):22
[12]Zhou Wei(周伟),Zhou Lian(周廉),Yu Zhentao(于振涛).Rare Metal Materials and Engineering(稀有金属材料与工程)[J],2005,34(6):1002
[13]Lu Yi(卢毅),He Xiaocong(何晓聪),Wang Yifeng(王医锋)et al.Journal of Aeronautical Materials(航空材料学报)[J],2015,35(6):48
[14]Liu Xiaoyan(刘晓燕),Zhao Xicheng(赵西成),Yang Xirong(杨西荣)et al.Heat Treatment of Metals(金属热处理)[J],2013,38(1):92
[15]Peng Jian(彭剑),Zhou Changyu(周昌玉),Dai Qiao(代巧)et al.Rare Metal Materials and Engineering(稀有金属材料与工程)[J],2013,42(3):483
[16]Chang Le,Zhou Changyu,Peng Jian et al.Rare Metal Materials and Engineering[J],2017,46(7):1803
[17]Zhao Naiqin(赵乃勤).Principle and Process of Heat Treatment(热处理原理与工艺)[M].Beijing:Metallurgical Industry Press,2009:86
[18]Zhang Guodong(张国栋).Thesis for Master(硕士论文)[D].Beijing:Beijing Jiaotong University,2016
[19]Wang Cheng(王成),Zhao Xicheng(赵西成),Yang Xirong(杨西荣)et al.Materials for Mechanical Engineering(机械工程材料)[J],2010,34(5):23
[20]Guo N,Song B,Guo C F et al.Materials&Design[J],2015,83:270
[21]Sun Qiaoyan(孙巧艳),Zhu Ruihua(朱蕊花),Liu Cuiping(刘翠萍)et al.The Chinese Journal of Nonferrous Metals(中国有色金属学报)[J],2006,16(4):592
[22]Zhang X H,Tang B,Zhang X L et al.Transactions of Nonferrous Metals Society of China[J],2012,22(3):496
[23]Zhang Ruoyu(张偌雨).Thesis for Master(硕士论文)[D].Chongqing:Chongqing University,2011
[24]Song B,Guo N,Xin R et al.Materials Science&Engineering A[J],2016,650:300
[2]Xing Jian(邢健),Ju Jianhui(巨建辉),Yang Liying(杨英丽)et al.Rare Metal Materials and Engineering(稀有金属材料与工程)[J],2013,42(8):1617
[3]Chang L,Zhou C Y,He X H.Metals-Open Access Metallurgy Journal[J],2017,7:99
[4]Wu Zhiyu(吴志煜).Thesis for Master(硕士论文)[D].Kunming:Kunming University of Science and Technology,2012
[5]Liu Ruitang(刘瑞堂),Zhou Xinping(周欣萍),Yin Jiancheng(尹建成)et al.Materials for Mechanical Engineering(机械工程材料)[J],2006,30(5):84
[6]Xia Xingyou(夏兴有).Thesis for Master(硕士论文)[D].Harbin:Harbin Engineering University,2007
[7]He Yunzeng(何蕴增),Zou Guangping(邹广平),Pan Xinji(潘信吉)et al.Journal of Experimental Mechanics(实验力学)[J],1994,9(3):262
[8]Guo N,Li X X,Xiao M et al.Advanced Engineering Materials[J],2016,18(10):1738
[9]Zhou Li(周利).Acta Mechanica Solida Sinica(固体力学学报)[J],1994,15(2):185
[10]Li Z.Acta Mechanica Solida Sinica[J],1994,107(3):229
[11]Jia Xiangya(贾祥亚),Liu Yinqi(刘茵琪),Qu Yinhua(曲银化)et al.Development and Application of Materials(材料开发与应用)[J],2013(5):22
[12]Zhou Wei(周伟),Zhou Lian(周廉),Yu Zhentao(于振涛).Rare Metal Materials and Engineering(稀有金属材料与工程)[J],2005,34(6):1002
[13]Lu Yi(卢毅),He Xiaocong(何晓聪),Wang Yifeng(王医锋)et al.Journal of Aeronautical Materials(航空材料学报)[J],2015,35(6):48
[14]Liu Xiaoyan(刘晓燕),Zhao Xicheng(赵西成),Yang Xirong(杨西荣)et al.Heat Treatment of Metals(金属热处理)[J],2013,38(1):92
[15]Peng Jian(彭剑),Zhou Changyu(周昌玉),Dai Qiao(代巧)et al.Rare Metal Materials and Engineering(稀有金属材料与工程)[J],2013,42(3):483
[16]Chang Le,Zhou Changyu,Peng Jian et al.Rare Metal Materials and Engineering[J],2017,46(7):1803
[17]Zhao Naiqin(赵乃勤).Principle and Process of Heat Treatment(热处理原理与工艺)[M].Beijing:Metallurgical Industry Press,2009:86
[18]Zhang Guodong(张国栋).Thesis for Master(硕士论文)[D].Beijing:Beijing Jiaotong University,2016
[19]Wang Cheng(王成),Zhao Xicheng(赵西成),Yang Xirong(杨西荣)et al.Materials for Mechanical Engineering(机械工程材料)[J],2010,34(5):23
[20]Guo N,Song B,Guo C F et al.Materials&Design[J],2015,83:270
[21]Sun Qiaoyan(孙巧艳),Zhu Ruihua(朱蕊花),Liu Cuiping(刘翠萍)et al.The Chinese Journal of Nonferrous Metals(中国有色金属学报)[J],2006,16(4):592
[22]Zhang X H,Tang B,Zhang X L et al.Transactions of Nonferrous Metals Society of China[J],2012,22(3):496
[23]Zhang Ruoyu(张偌雨).Thesis for Master(硕士论文)[D].Chongqing:Chongqing University,2011
[24]Song B,Guo N,Xin R et al.Materials Science&Engineering A[J],2016,650:300
© 2004-2018 中国地质图书馆版权所有 京ICP备05064691号 京公网安备11010802017129号 地址：北京市海淀区学院路29号 邮编：100083 电话：办公室：(+86 10)66554848；文献借阅、咨询服务、科技查新：66554700 |